To remove the stand from your ASUS VN248 monitor, first lay the monitor face down on a smooth, clean surface. Next, remove the four rubber covers hiding the four screws in the rear of the monitor. You can do this by prying out the plastic covers with a stiff, pointed tool, such as a metal spudger. Once the covers are removed, take out the four 13.4 mm Philips #1 screws securing the monitor stand. Finally, simply remove the stand from the display.
Characteristics | Values |
---|---|
Steps to remove the stand | 1. Lay the monitor face down on a smooth, clean surface |
2. Remove the rubber covers in the four screw holes | |
3. Remove the four 13.4 mm Philips #1 screws securing the monitor stand | |
4. Remove the stand from the display | |
Tools required | Stiff pointed tool, like a metal spudger |
Other recommendations | Cover the table surface with a soft cloth to prevent damage to the monitor |
What You'll Learn
Lay the monitor face down on a smooth, clean surface
To remove the stand from your ASUS VN248 monitor, start by laying the monitor face down on a smooth, clean surface. This is important to protect the screen from scratches or other damage. Make sure the surface is completely flat and free of debris that could potentially scratch or damage the screen.
If your table or work surface is particularly hard, it is recommended to cover it with a soft cloth to provide an extra layer of protection for your monitor. This is especially important if your monitor has a glass screen, as glass is more prone to cracking or chipping if it comes into contact with a hard surface.
Once you have found a suitable location, carefully lay the monitor face down, ensuring that the screen does not come into contact with any objects that could cause damage. Take your time with this step to ensure the safety of your monitor.
Now that the monitor is securely in place, you can proceed to the next steps of removing the stand, which involve removing the screws and rubber covers.
Monitoring Internet Usage: A Guide for Modem Users
You may want to see also
Remove the rubber covers from the rear of the monitor
To remove the rubber covers from the rear of the monitor, you will need a stiff, pointed tool, such as a metal spudger. These rubber covers are hiding the screws that secure the monitor stand in place, so you will need to carefully pry them out. This will expose the four 13.4 mm Philips #1 screws that you will need to remove with a screwdriver to detach the stand. Make sure you lay the monitor face down on a smooth, clean surface before you begin, and cover the table with a soft cloth to prevent damage to the screen.
Monitoring Internet Usage: Security, Productivity, and Privacy
You may want to see also
Unscrew the stand from the display
To remove the stand from your ASUS VN248 monitor, you will need to first lay the monitor face down on a smooth, clean surface, preferably covered with a soft cloth to prevent damage.
Next, you will need to locate the four rubber covers that hide the screws securing the monitor stand in place. Use a stiff, pointed tool, such as a metal spudger, to carefully pry out these plastic covers. Be gentle to avoid damaging the monitor.
Once the rubber covers are removed, you will see four screws that need to be unscrewed. Use a screwdriver to remove these screws. The size of the screws is 13.4 mm Philips #1. Make sure to keep track of the screws as you remove them so you can easily reassemble the stand if needed.
After removing the screws, you can now carefully lift and remove the stand from the display. Be gentle and take your time to avoid damaging any of the components.
Now that you have successfully unscrewed and removed the stand from the display, you can proceed with any desired adjustments or replacements. Remember to follow the instructions in reverse order to reassemble the stand if needed.
Adjusting Brightness on Your ASUS Monitor: A Simple Guide
You may want to see also
Pull the display bezel straight up
To remove the display bezel from your ASUS VN248 monitor, you'll need to be careful not to damage the LCD. It's best not to use any prying tools on the display bezel, as this could cause damage. Instead, use your fingers to pull the bezel straight up and away from the rear case.
Before you begin this process, lay the monitor face down on a smooth, clean surface. Cover one of the long edges of the display with a thin cloth. This will protect your fingertips and prevent smudging on the LCD. Grip the side of the bezel through the cloth and lift straight up. You should feel a few plastic clips pop free in the centre.
Repeat this process for the remaining three sides. Move to the other long side and lift up on the centre of the bezel. Then, grip the centre of the final side and lift the bezel away from the rear case.
Now that you've freed the centres of the four sides, you can move on to the corners. Each corner is secured by two large clips that can't be freed by just pulling straight up like you did with the sides. You'll need to use a thin, stiff prying device, like a Jimmy, to press in against the bottom clip in the lower left corner (beneath the HDMI logo). While pressing the clip in, pull up on the lower edge of the bezel. The entire corner should pop free.
Once you've freed one corner, gently twist the bezel to free the remaining corners.
Monitoring Internet Usage: Netgear Genie's Parental Controls
You may want to see also
Repeat the procedure around the display
To remove the bezel from your ASUS VN248 monitor, you'll need to repeat the procedure around the display. Here's a detailed guide:
- Lay a cloth over one of the long edges of the display: This will protect both the display and your fingertips as you work.
- Grip the side of the bezel through the cloth and lift straight up: Be careful to only pull straight up and not to pry against the display, as pushing down on it could damage the LCD.
- Repeat this process on the other long side: Move to the opposite long side of the display and lift up on the center of the bezel.
- Grip the center of the final side and lift the bezel away: By lifting the bezel away from the rear case, you'll free the centers of all four sides.
- Work on the corners: Each corner is secured by two large clips that can't be freed by simply pulling straight up. You'll need to use a thin, stiff prying device like a Jimmy.
- Press in against the bottom clip: Using your prying tool, press in against the bottom clip in the lower left corner, located beneath the HDMI logo.
- Pull up on the lower edge of the bezel: While continuing to press the clip in, gently pull up on the lower edge of the bezel. The entire corner should pop free.
- Gently twist the bezel: Once one corner is free, you should be able to gently twist and remove the bezel, freeing all the remaining corners.
By following these steps, you'll be able to safely and effectively remove the bezel from your ASUS VN248 monitor. Remember to work carefully and avoid applying pressure directly to the display to prevent any damage.
Monitoring Memory Usage: NRPE Nagios Guide
You may want to see also
Frequently asked questions
To remove the stand from your ASUS VN248 monitor, first lay the monitor face down on a smooth, clean surface. Then, remove the four rubber covers that are hiding the four screws in the rear of the monitor. After that, simply unscrew the four screws and remove the stand from the display.
Yes, you will need a stiff, pointed tool to pry out the rubber covers. A metal spudger or a thin, stiff prying device like a Jimmy should do the trick.
It is recommended to use a thin cloth to protect your fingertips and prevent smudging the LCD. Lay the cloth over one of the long edges of the display, grip the side of the bezel through the cloth, and lift straight up. Be careful to only pull straight up and not to pry against the display, as pushing down on it could damage it.