Resetting Your Q-See Camera: A Step-By-Step Guide

how to factory rest q see camera

If you're looking to reset your Q-See camera to factory settings, there are a few different methods you can try. One method is to press and hold the power button for 10 seconds to turn off the camera, then remove the battery cover, hold down the power button for 30 seconds, reinstall the battery cover, and turn on the camera. Another method is to set the mode dial to P, press the menu/set button, select the setup option, scroll through the setup listings until you find 'reset', and select this option. Finally, if you are trying to reset your Q-See DVR, press and hold the Menu button on the front of the device for 3 seconds, then release and press OK, press Select to choose Settings, press OK to confirm, and finally, press Delete to erase all settings on the device.

shundigital

Resetting Q-See QC444 Video Surveillance System

The Q-See QC444 Video Surveillance System is a 4-channel DVR with a pre-installed 500GB hard drive, offering both CIF and D1 recording options. The system supports up to 4 cameras simultaneously and allows for remote monitoring via PC, MAC, or supported 3G smartphones.

To reset the Q-See QC444 Video Surveillance System, follow these steps:

  • Press and hold the "Menu" button on the front of the device for 3 seconds.
  • Release the "Menu" button and press the "OK" button.
  • Press the "Select" button to access the "Settings" menu.
  • Press the "OK" button again to confirm your selection.
  • Press the "Delete" button to initiate the factory reset and erase all settings on the device.

Alternatively, you can perform a factory reset by pressing and holding the power button for 10 seconds. This will turn off the device and reset it to its original settings.

It is important to note that performing a factory reset will erase all custom settings and return the device to its default configuration. Ensure that you back up any important data before proceeding with the reset.

If you have forgotten your password, there is a way to reset it. Keep the system on the main screen, then press the "Pause" button ten times. This will reset the system, and the default password will be set to pressing the "CH1" button six times.

For more detailed instructions and troubleshooting information, refer to the Q-See QC444 User Manual. It provides comprehensive information on the features, specifications, installation, and operation of the Q-See QC444 Video Surveillance System.

shundigital

Resetting Q-See DVR

Resetting your Q-See DVR will depend on what you are trying to achieve. If you are looking to reset your DVR to its factory settings, there are a few methods you can try.

Firstly, if you have forgotten your password, you can reset it by keeping the system on the main screen and then pressing the "Pause" button ten times. The DVR will then reset the system. After this, the default password will be the "CH1" button pressed six times.

If you are looking to reset your DVR to its factory settings, you can do so by following these steps:

  • Press and hold the "Menu" button on the front of the device for 3 seconds.
  • Release the "Menu" button and press the "OK" button.
  • Press the "Select" button to select "Settings".
  • Press the "OK" button to confirm your selection.
  • Press the "Delete" button to erase all settings on the device.

Alternatively, you can try pressing and holding the power button for 10 seconds.

If you are looking to restore your Q-See DVR, you can do so by following these steps:

  • Log in to the NVR and navigate to "Main Menu > System > Restore" to access the restore page.
  • Choose the items you want to restore or select "Select All" and click "OK" to save the settings.

Note that the system will automatically reboot once the factory settings are successfully restored.

It is important to note that Q-See takes security very seriously. They deliberately make it extremely difficult to get into a Q-See DVR without the password. If you are unable to reset your DVR using the methods outlined above, you may need to contact Q-See Customer Service for assistance.

shundigital

Resetting a Q-See camera without a reset button

If your Q-See camera does not have a reset button, you can try the following methods to reset it to factory settings. Please note that the effectiveness of these methods may vary depending on the model and firmware version of your camera.

Firstly, if you have access to the camera's physical body, you can try to locate a small pinhole or door on the rear or bottom of the camera. This door may be fastened with screws and can be opened using a paper clip or similar tool. Inside, you should find a reset button that you can press to initiate the reset process.

If your camera is a POE (Power over Ethernet) model, you may need to connect it to a non-POE switch or router to power it on and access the reset function. Alternatively, you can try using a tool such as SADP (provided by the camera manufacturer) to reset the password or extract the firmware.

If the above methods are not applicable or successful, you may need to contact the manufacturer's customer support for further assistance. It is important to note that performing a factory reset will erase all custom settings and data on your camera, including your password. Ensure that you have the necessary information to set up the camera again after the reset process.

  • Power off your camera and unplug the power cord from the unit.
  • If applicable, remove any screws or covers that are holding the camera's casing in place.
  • Locate the reset button, which may be inside a small door or behind a pinhole.
  • Press and hold the reset button for at least 10 seconds.
  • Release the button, and then plug the power cord back in.
  • Wait for the camera to boot up, which may take around 30 seconds.
  • Enter your cable login information to set up the camera again.

Additionally, if you have forgotten your password, there is a method to reset it without performing a full factory reset. To do this, keep the system on the main screen and press the "Pause" button ten times. The DVR will reset, and the default password will be set to " [CH1]" followed by pressing the "CH1" button six times.

shundigital

Resetting a Q-See camera with a reset button

For Q-See QC444 Video Surveillance System:

  • Set the mode dial to P.
  • Press the menu/set button.
  • Select the setup option.
  • Scroll through the setup listings until you find 'reset'.
  • Select the reset option.
  • Once the camera has reset, turn it off and back on again.
  • Set the date and time when prompted.

For Q-See QC888 NVR and QCW2MPSL beacon wifi camera:

With the power on, press and hold the button under the plate for at least 15 seconds until the light changes.

For Q-See DVR:

  • Press and hold the power button for 10 seconds to turn off the DVR.
  • Remove the battery cover.
  • Hold down the power button for 30 seconds to reset the DVR.
  • Reinstall the battery cover and turn on the DVR.

For Q-See DVR (alternative method):

  • Power off the DVR.
  • Unplug the power cord from the back of the unit.
  • Press and hold the reset button for about 10 seconds.
  • Release the reset button and plug in the power cord.
  • Wait about 30 seconds for the DVR to boot up.
  • Enter your cable login information.

Please note that the specific steps to reset a Q-See camera may vary depending on the model and firmware version, so it is always recommended to refer to the user manual or seek support from the official website for the most accurate and up-to-date instructions.

shundigital

Resetting a Q-See camera's password

Resetting the password for your Q-See camera can be done by performing a factory reset. Here is a step-by-step guide on how to do this:

Step 1:

First, decide which method you would like to use to reset your Q-See camera. There are a few different ways to reset your device, depending on the model of your camera and your specific situation.

Step 2: Using the "Menu" Button:

If your Q-See camera has a "Menu" button, you can try the following steps:

  • Press and hold the "Menu" button on the front of the device for 3 seconds.
  • Release the "Menu" button and press the "OK" button.
  • Press the "Select" button to choose "Settings."
  • Press "OK" to confirm.
  • Finally, press the "Delete" button to erase all settings, including your password, and restore the device to its factory default settings.

Step 3: Using the Power Button:

If you don't have a "Menu" button, or if the above method doesn't work, you can try using the power button:

  • Press and hold the power button for 10 seconds to turn off your Q-See camera.
  • Remove any connected cables, such as the power cord or battery.
  • Wait for at least 30 seconds.
  • Reconnect the power cord or reinstall the battery to turn on your camera.

Step 4: Resetting Without a Password:

If you have forgotten your password and are unable to log in, you can try the following method:

  • Power off your Q-See device and unplug the power cord from the back of the unit.
  • If your device has a battery, remove it.
  • Press and hold the reset button for about 10 seconds. This button may be located under a plate or cover.
  • Release the reset button and plug the power cord back in.
  • Wait for your Q-See camera to boot up, which may take up to 30 seconds.
  • Set up your device and create a new password.

Step 5: Resetting a Specific Model:

If you own a Q-See QSD004C4-250 camera, you can reset your password by following these steps:

  • Keep your system on the main screen.
  • Press the "Pause" button ten times.
  • Your DVR will reset, and the default password will be set to pressing the "CH1" button six times.

Please note that performing a factory reset will erase all your settings and data, so make sure to back up any important information before proceeding. Additionally, the specific steps may vary slightly depending on the model of your Q-See camera, so refer to the user manual for detailed instructions if the above steps do not work for your device.

Frequently asked questions

To reset your Q-See camera, you need to follow these steps:

- Set the mode dial to P.

- Press the menu/set button.

- Select the setup option.

- Scroll through the setup listings until you get to 'reset'.

- Select the reset option.

- Once the camera has reset, turn it off and back on again.

- Set the date and time.

If you can't find the reset option, try the manual reset process:

- Turn off the camera.

- Remove the battery pack.

- Remove the button-sized lithium battery.

- Wait for 30 seconds.

- Reinsert the button-sized lithium battery.

- Reinsert the battery pack.

If you can't find a reset button, try the following:

- Press and hold the power button for 10 seconds to turn off the DVR.

- Remove the battery cover.

- Hold down the power button for 30 seconds to reset the DVR.

- Reinstall the battery cover and turn on your DVR.

To reset your Q-See DVR to factory settings, follow these steps:

- Press and hold the Menu button on the front of the device for 3 seconds.

- Release the Menu button and press the OK button.

- Press the Select button to select Settings.

- Press the OK button to confirm your selection.

- Press the Delete button to erase all settings on the device.

The default password for Q-See cameras is "qsee".

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment