Removing Monitor Hole Covers: A Step-By-Step Guide

Removing the back cover of a monitor can be a challenging task and it is important to proceed with caution to avoid causing any damage. In some cases, it may not be possible to remove the cover without the use of tools and a certain level of force. It is always recommended to refer to the monitor's manual for specific instructions, however, if this is unavailable, there are some general steps that can be followed. Firstly, it is crucial to disconnect all cables from the monitor, including the power cord. Then, one can attempt to locate and remove any screws holding the monitor together, being careful not to apply too much force as this may result in broken tabs and dents. After removing the screws, a flat-head tool or even one's hand can be used to gently pry the cover off, starting from the sides and working around the seams of the monitor. If this does not work, one can try using a guitar pick or a flathead screwdriver wrapped in cloth to gently pry the cover off. It is important to note that attempting to remove the back cover of a monitor may void the warranty, and one should proceed at their own risk.

Removing the back cover of a Samsung monitor

To remove the back cover of a Samsung monitor, first disconnect the power cable and any other peripherals connected to the monitor. Place the monitor screen-side down on a soft cloth on a stable surface.

If your model has a stand, you will need to remove this. On some models, the stand is screwed into the base, while on others, it snaps in with plastic tabs. Use the appropriate tool for your model.

Now you can begin to remove the back panel. Remove all the case screws fastening the back panel to the front panel. These screws are located around the perimeter of the back panel and in the middle. Once all the screws have been removed, you should be able to lift off the back panel and expose the internal components.

To remove the back cover, or "cover terminal", grab it with your finger from the hole where the cables go through. Pull it down and back. The tabs on the top edge should come out first, and then you can work the top edge out. It should then come out neatly. You may need to use a little force, but no tools.

Removing the back cover of an Asus monitor

To remove the back cover of an Asus monitor, you will need to first lay the monitor face down on a smooth, clean surface. Next, remove the four rubber covers that are hiding the screws in the rear of the monitor. You can do this by prying out the plastic covers with a stiff, pointed tool, such as a metal spudger. Once the covers are removed, you can then unscrew the four screws securing the monitor stand and remove the stand from the display.

The display bezel is held in place by plastic clips that can be released by pulling straight up on the bezel. It is recommended to use your fingers for this step rather than a prying tool, as this could damage the LCD. Place a thin cloth over one of the long edges of the display and grip the bezel through the cloth to protect your fingertips and prevent smudging on the LCD. Lift straight up on the bezel, starting with the long edges and then moving to the shorter sides. Be careful to pull straight up and not to pry against the display, as pushing down on it could cause damage.

Each corner of the bezel is secured by two large clips that cannot be freed by simply pulling straight up. Using a thin, stiff prying device, press in against the bottom clip in the lower left corner of the bezel (beneath the HDMI logo) while simultaneously pulling up on the lower edge. The entire corner should pop free. Repeat this process on the other corners as needed. Once one corner is freed, you should be able to gently twist the bezel off, releasing the remaining corners.

With the back cover removed, you can now access the internals of the monitor for further disassembly or repair.

Removing the back cover of a monitor with no VESA holes

Step 1: Check for Hidden VESA Holes

Before starting the removal process, it is important to double-check that your monitor indeed does not have VESA holes. Sometimes, manufacturers hide these holes in plain sight, so a thorough inspection is recommended.

Step 2: Dismantle the Monitor

If your monitor truly does not have VESA holes, you may need to dismantle it to access the stand removal screws. This process can vary depending on the make and model of your monitor. It is important to proceed with caution, as forcefully removing components can damage your monitor.

For example, in the case of a Samsung monitor, one user suggested removing the screws from the bottom bezel. However, this may not be the same for all Samsung monitors or other monitor brands. Thus, it is crucial to refer to your monitor's manual or seek brand-specific guidance.

Step 3: Remove the Factory Stand

Once you have successfully dismantled the monitor, the next step is to remove the factory stand. This step may also vary depending on the monitor model. In some cases, you may need to disassemble the back panel of the monitor to access the necessary screws. Removing the factory stand is crucial, as it will get in the way of the VESA adapter and will be an eyesore if you plan to use an aftermarket mount.

Step 4: Install a VESA Adapter

With the factory stand removed, you can now install a VESA adapter. VESA adapters are brackets that mount to other features of your monitor and provide mountable VESA holes. There are various types of VESA adapters available, including budget options, low-visibility adapters, and monitor-specific adapters.

When choosing a VESA adapter, consider the size and weight of your monitor, as well as the desired visibility of the adapter. Some adapters have arms that reach the top and bottom of the monitor, while others are designed to be more discreet.

Additionally, some monitors may require specific VESA adapters, so it is worth searching for an adapter designed for your monitor model.

Step 5: Mount Your Monitor

After installing the VESA adapter, you can now mount your monitor to the wall or a monitor arm. Ensure that you follow the instructions provided with your chosen mounting hardware to ensure a safe and secure installation.

It is important to note that removing the back cover of a monitor with no VESA holes may void your warranty. Additionally, improper removal or installation of components may damage your monitor. Thus, it is crucial to proceed with caution and seek guidance specific to your monitor model when necessary.

Dismantling a monitor

Step 1: Prepare Your Workspace

Before you begin, make sure you have a soft, flat surface to work on. This will help protect the monitor from any scratches or damage during the dismantling process. It is also recommended to have a magnetic Phillips screwdriver with a long, thin neck, as this will come in handy later on.

Step 2: Remove the Back Cover

The first step is to remove the back cover of the monitor. This will usually involve removing a few screws, which are typically located at the bottom of the monitor. Be careful not to pull too hard on the plastics, and use a pry tool to gently loosen the cover if needed.

Step 3: Disconnect Internal Components

Once the back cover is removed, you will see the internal components of the monitor. Be careful not to touch any of the electronic components, as this could result in an electric discharge. Identify the cables and wires that need to be disconnected, and gently unplug them.

Step 4: Remove the Monitor's Plastic Frame

The next step is to remove the plastic frame of the monitor. This will involve removing a few more screws and carefully detaching the frame from the rest of the monitor. Be cautious around the cabling when removing the frame to avoid any damage.

Step 5: Separate the LCD and Backlight Layers

At this point, you will be able to see the different layers of the monitor: the backlight layer, the diffuser sheet, and the LCD layer. The outermost protective plastic or glass layer is glued to the LCD and cannot be removed. However, you can carefully remove the diffuser sheet and clean it if needed.

Additional Tips:

• When removing screws, try to remember the force you used to unscrew them. Reapply the same force when reassembling to prevent damage.
• If you accidentally drop a screw inside the monitor, don't panic. Try rattling the monitor gently to see if you can locate it. If it's at the bottom and not causing any issues, you may want to leave it there.
• Be very careful when prying open the bezel, as there may be connection wires still attached. Gently pry it open and ignore any broken pieces, as these are likely just jagged edges from the plastic sections.

Video Tutorials and Manuals:

If you are unsure about any of the steps, it is recommended to refer to video tutorials or official manuals for your specific monitor model. Websites like iFixit and YouTube offer a wealth of resources and step-by-step guides for dismantling various types of monitors.

Remember to proceed with caution and be gentle with the internal components to avoid causing any damage to your monitor. Good luck with your project!

Drilling DIY VESA holes

Step 1: Prepare the Monitor

Before you begin drilling, make sure your monitor is turned off and unplugged for safety. Place the monitor face down on a soft surface to protect the screen from any damage.

Step 2: Measure and Mark the Hole Locations

Using the VESA mount as a guide, measure and mark the locations of the holes on the back of your monitor. It is crucial to be accurate in this step to ensure proper alignment. You can use a ruler or a measuring tape for precise measurements.

Step 3: Choose the Right Drill Bit

Select a drill bit that matches the size of the VESA holes. It is important to use the correct bit size to ensure a secure fit for your mount.

Step 4: Start Drilling

Gently and slowly start drilling at the marked locations. Make sure to apply even pressure and maintain a steady pace to avoid slipping or damaging the monitor. Take your time and go slowly to prevent any mistakes.

Step 5: Secure the VESA Mount

Once you have successfully drilled the holes, attach the VESA mount to the back of your monitor using the appropriate screws. Ensure that the screws are tight and secure.

Step 6: Test the Setup

After securing the VESA mount, carefully flip the monitor and attach it to the desired mounting surface, such as a wall or a stand. Ensure that the monitor is firmly attached and test the stability by gently pushing or pulling the monitor.

It is important to note that drilling your own VESA holes comes with risks, and it is always recommended to seek professional help if you are unsure about the process. Additionally, always prioritize safety by wearing protective gear, such as safety goggles, when operating power tools like a drill.

Frequently asked questions