Removing A Viewsonic Monitor From Mount: A Step-By-Step Guide

If you're looking to remove your ViewSonic monitor from its mount, you've come to the right place. In this guide, we'll take you through the step-by-step process of safely detaching your monitor from its current setup, whether it's a standard or LCD flat-screen model. Before we begin, it's important to note that you should always place your monitor on a flat, stable surface to avoid any potential damage or injury. Now, let's get started!

Unplug the monitor power cord from the power source

Before you begin to remove your ViewSonic monitor from its mount, it is important to disconnect the monitor from its power source. This is a crucial safety step to ensure that the monitor is turned off and there is no risk of electric shock during the removal process.

To unplug the monitor power cord from the power source, start by locating the power cord. The power cord is the cable that connects the monitor to an electrical outlet or power strip. It is usually located at the back of the monitor, near the base or stand. Once you have located the power cord, follow it to the power source, which may be an electrical outlet on the wall or a power strip on your desk.

Now, you can unplug the power cord. Grip the power cord firmly but gently, and then pull it straight out from the power source. Be careful not to bend or twist the cord excessively, as this could damage the cable or the connector. If you find it difficult to remove, check that you have correctly identified the power cord and that it is not tangled or caught on anything. If the cord is difficult to reach or remove, unplugging it safely should be your priority. Consider moving the monitor closer to the power source or using a different outlet if available.

Once the power cord is unplugged, set it aside in a safe place where it will not be accidentally knocked or pulled. Ensure that the cord is not placed in a position where it could present a tripping hazard. If the cord is coiled, avoid placing heavy objects on top of it, as this may damage the cable.

With the power cord safely unplugged and set aside, you can now proceed with the next steps to remove your ViewSonic monitor from its mount, knowing that you have taken the necessary precautions to ensure a safe process.

Disconnect the monitor cables from the computer

Before disconnecting the monitor cables from the computer, ensure you have unplugged the monitor power cord from the power source. This is an important safety step.

Now, to disconnect the monitor cables from the computer:

Start by locating the cables that connect your ViewSonic monitor to your computer. These cables will likely include a power cable and a video cable, such as HDMI, DVI, or VGA.

Once you have identified the cables, gently grasp each cable connector and carefully pull it straight out from the relevant port on the back of the monitor. Be careful not to bend or damage the connectors or ports.

If the cables are secured with screws or other fasteners, be sure to loosen or remove them before disconnecting the cables.

After disconnecting all the cables, it is a good idea to tie or wrap the cables neatly to avoid any tangles or damage during the rest of the removal process.

Now that the monitor cables have been safely disconnected from the computer, you can proceed with the next steps to remove the ViewSonic monitor from its mount. Remember to handle the monitor with care and follow the specific instructions for your monitor model.

Place the monitor on its side on a towel

To remove your ViewSonic monitor from its mount, you'll first need to unplug the monitor power cord from the power source and disconnect the monitor cables from the computer. Place a towel on a flat surface, such as a table or desk, and then carefully lay the monitor on its side on the towel. This step is important to avoid damaging the screen, especially if your monitor has a curved screen.

Now that the monitor is on its side, you can begin the process of detaching the monitor base. For standard ViewSonic monitors, you'll need to slide the monitor base forward to access the locking tab on the sub-base. The sub-base is the component that connects the monitor to its base, and the base pivots on this sub-base. Once you've located the locking tab, pull it up with your thumb and slide the sub-base towards the front of the monitor. You should now be able to remove the sub-base and the base away from the monitor.

For ViewSonic LCD flat-screen monitors, the process is slightly different. After laying the monitor on its side on a towel, you'll need to unplug the monitor power cord and disconnect it from the computer. Then, place the monitor screen side down on the towel. Locate the locking knob on the bottom of the base and turn it counterclockwise 90 degrees with your fingers. Finally, pull the base off the monitor.

Slide the monitor base forward to access the locking tab

To remove the ViewSonic monitor base, you must first unplug the monitor power cord from the power source and disconnect the monitor cables from the computer. Place a towel on a flat surface and lay the monitor on its side on the towel. Many standard monitors use a curved screen, so laying the monitor on its side avoids damaging the screen.

Now, slide the monitor base forward to access the locking tab on the sub-base. The sub-base connects to the bottom of the monitor, and the base pivots on the sub-base.

The locking tab is a crucial component that secures the monitor base to the sub-base. By sliding the monitor base forward, you gain access to this locking mechanism. This step is essential for the safe and effective removal of the monitor base.

Once you have accessed the locking tab, you can proceed to the next step of removing the monitor base. It is important to follow the correct sequence of steps to ensure the process is safe and does not cause any damage to the monitor or its components.

In the next step, you will need to pull up on the locking tab with your thumb and slide the sub-base toward the front of the monitor. This action will release the lock and allow you to separate the sub-base and base from the monitor.

Remove the sub base and base from the monitor

To remove the sub base and base from the monitor, you will need to first place the monitor on a flat surface. If your monitor has a curved screen, place it on its side to avoid damaging the screen.

Next, slide the monitor base forward to access the locking tab on the sub-base. The sub-base connects to the bottom of the monitor, and the base pivots on the sub-base. Pull up on the locking tab with your thumb, and slide the sub-base toward the front of the monitor. Now, you can remove the sub-base and base away from the monitor.

If your monitor has screws attaching the base, you will need to remove these first. On some models, there are two screws on each side of the arm portion of the stand. Unscrew one from each side, and then, without pulling forward or backward, slide the arm down and out of the slot. A metal bracket from inside the monitor will come out with it. You may need to wiggle the arm slightly from side to side.

Frequently asked questions