Removing Gateway Monitor Base For Wall Mounting

If you're looking to remove the base of an old Gateway monitor so that you can mount it on a wall, there are a few things you should keep in mind. First, make sure you have the original instructions for putting the monitor together, as attempting to remove the base the wrong way could damage your monitor. Next, check for hidden screws—these could be near the neck of the stand or under a panel about one-third of the way up from the bottom. There may also be screws that are only accessible from the bottom of the stand. Once you've found and removed all the screws, you should be able to lift the stand off the monitor. Additionally, some monitors have a small release lever at the back of the swivel base—push this down and then hit the swivel base towards the back to lift the unit up.

Look for hidden screws near the neck of the stand

To remove the base of your Gateway monitor, you will need to detach the stand. This process will involve locating and removing screws.

Start by examining the neck of the stand for any hidden screws. Look carefully, as they may be concealed under a panel or other component. In some cases, you may need to access the screws from the bottom of the stand.

If you cannot locate any screws near the neck of the stand, try looking at the back of the monitor. There may be a small release lever at the back of the swivel. Push it down and then hit the swivel base towards the back before lifting the unit up.

Alternatively, you may need to remove the back panel or part of it to access the screws underneath. Once you have removed all the necessary screws, you should be able to detach the stand and proceed with mounting your monitor on the wall.

Check the bottom of the stand for screws

When removing the base of a Gateway monitor for wall mounting, it is important to check the bottom of the stand for screws. This is because the stand is usually attached to the bottom of the monitor and held in place by screws.

To begin the process of removing the stand, first ensure that the monitor is turned off and unplugged. Place a soft cloth on a table to prevent the monitor screen from getting scratched. Then, turn the monitor upside down and check the bottom of the stand for screws. If there are screws present, use a screwdriver to unscrew them. Once the screws have been removed, the stand should be able to be lifted off of the monitor.

In some cases, there may be hidden screws that are not visible from the outside of the stand. If no screws are visible at the bottom of the stand, try looking for hidden screws near the "neck" of the stand, under a panel about one-third of the way up from the bottom. There may also be screws that are only accessible from the bottom of the stand. If you push in the tab on the neck of the base and pull on the bottom of the base, the bottom of the stand should pull out and the screws will become accessible.

It is important to note that attempting to remove the monitor stand in the wrong way could lead to complications later on, as other components of the stand may not work properly. Therefore, if you are unable to locate the screws or are unsure about how to remove the stand, it is recommended to refer to the user manual or seek assistance from a local electronic repair shop.

Find the release lever on the back of the swivel

To remove the base of your Gateway monitor, you'll need to locate the release lever on the back of the swivel mechanism. This lever is typically small and may be difficult to spot, but finding it is key to detaching the monitor from its base. Here's a step-by-step guide to help you through the process:

• Locating the Release Lever: Start by examining the back of the swivel, which is the part of the stand that connects the monitor to its base and allows it to rotate. Look for a small lever, tab, or button—this is the release mechanism. It may be located on the neck of the stand, about a third of the way up from the bottom, or it could be hidden under a panel.
• Preparing for Detachment: Once you've located the release lever, you may need to push it down or press it in. In some models, there might be an additional step where you need to hit the swivel base towards the back before proceeding.
• Detaching the Base: With one hand, continue holding the release lever in the pushed-down position. Now, with your other hand, carefully lift the unit up. You may need to apply some force to separate the two parts, but the base should come off, revealing the screws that were previously hidden.
• Accessing Hidden Screws: With the base removed, you can now access the screws that were hidden underneath. These screws are crucial for attaching your monitor to a wall mount. You may need to unscrew them to fully detach the base or to attach a new mounting bracket.
• Adjusting Monitor Position: Before attaching your monitor to the wall, you might want to adjust its position. You can do this by adjusting the tension, tilt, and swing of the monitor arm. Look for small hex bolts on the monitor mounting bracket and swivel arm bracket, and use an Allen wrench to adjust them as needed.
• Final Steps: Follow any remaining instructions specific to your wall mount to complete the process. Ensure that your monitor is securely attached to the wall, and you're done!

Remember to be gentle throughout the process to avoid damaging any parts of your monitor. If you're unsure about any steps, consult a professional or seek further guidance.

Check the user manual for instructions on how to remove the stand

If you want to remove the stand from your Gateway monitor to wall-mount it, the first thing you should do is check the user manual for instructions. The manual should contain specific instructions for your monitor model, and following these instructions is the best way to ensure you remove the stand safely and correctly.

If you don't have a physical copy of the user manual, you can usually find a digital copy online. To find the correct manual, you will need to know the model name and/or number of your monitor. This information is usually written on the front or back of the monitor. If you can't find it there, you can check the monitor's settings on your computer. Press the Windows + I key to open Settings, then go to System > Display. Under Related settings, select Advanced display, and you should see the details about your monitor under Display information.

Once you have found the correct user manual, follow the instructions provided to remove the stand. This may involve unscrewing screws, pressing buttons, or pulling the stand away from the monitor. Make sure you follow the instructions carefully to avoid damaging your monitor.

In some cases, the user manual may not provide clear instructions or may not be available at all. If this is the case, you can try looking for hidden screws that may be holding the stand in place. These screws could be located near the "neck" of the stand or under a panel on the stand. You may also need to remove the base of the stand to access the screws.

If you can't find any screws or other mechanisms holding the stand in place, you may need to gently pull the stand away from the monitor. Be very careful when doing this, as you don't want to damage the monitor or its screen. It's also a good idea to have someone help you hold the monitor steady while you pull the stand away.

Detach the vertical stand by pressing a button or looking for hidden screws

To detach the vertical stand, first check if there are any screws holding it in place. If there are, simply unscrew the stand from the monitor. If there are no screws, look for a button near or on the vertical stand. Some monitors, like Dell and Acer, require you to press a dedicated button to remove the stand. Press the button and gently pull the stand outwards. If it does not come out easily, try applying a small amount of mechanical oil to the joints to loosen it.

If your monitor does not have any screws or buttons, you may be able to remove the stand by gently pulling it away from the monitor. It is important to hold the monitor by its sides and not the screen to avoid damaging it.

In some cases, the vertical stand may be connected to a holder at the back of the monitor. To remove the holder, you may need to detach the back panel of the monitor. This will require removing all the screws from the back panel, gently lifting it off, and then disconnecting all the cables connecting the ports and buttons on the panel. Once the back panel is removed, you can access and remove the screws connecting the vertical stand holder. Finally, reassemble the monitor by connecting all the cables back in place.

Frequently asked questions