Removing Film From Your Asus Monitor: Step-By-Step Guide

The Asus Vz279 monitor is a popular choice for many people, but some users have reported an issue with a film appearing on the screen. This film can be unsightly and negatively impact the user experience, so it is important to know how to remove it. There are several methods that can be used to address this problem, and in this discussion, we will explore effective techniques for eliminating the film and restoring the monitor to its original condition.

Place the monitor face down on a table

To remove the film on your Asus monitor, you'll need to detach the arm/base. Start by placing the monitor face down on a table. It's recommended that you cover the table surface with a soft cloth to prevent any damage to the screen.

Now, look at the side of the stand. You should see an indent near the top. Take a flathead screwdriver and wedge it into this indent. You don't need to worry about causing any damage as you can't mess anything up at this stage. Once the screwdriver is in place, simply pop out the plastic top part of the stand.

This will expose the screws holding the remainder of the stand in place. With the screwdriver, you can now remove these screws and detach the rear hinge cover.

Now that the stand is removed, you can access and remove the film on your monitor.

Pry off the back plate

To pry off the back plate of your ASUS monitor, you will first need to lay the monitor face down on a table or another flat surface. Ensure the table surface is covered with a soft cloth to prevent damage to the screen.

Next, you will need to remove the rubbers or covers in the four screw holes. You can use a stiff, pointed tool, such as a flathead screwdriver or a metal spudger, to pry out these covers. Once the covers are removed, you can access the screws holding the back plate in place.

Now, use your screwdriver to remove the screws. Again, be careful not to scratch or damage the screen while doing so. With the screws removed, you can carefully pry off the back plate.

If you are having trouble removing the back plate, try using a thin, stiff prying device, such as a flathead screwdriver, to gently wedge between the back plate and the monitor. This should help pop the back plate off without causing any damage.

By carefully following these steps, you should be able to successfully pry off the back plate of your ASUS monitor.

Remove the screws holding the stand to the monitor

To remove the screws holding the stand to the monitor, you will need to first place the monitor face down on a table. Cover the table with a soft cloth to prevent damage to the screen.

Now, look at the back of the monitor stand. You will notice a plastic cover or back plate that needs to be removed to access the screws. Use a flat-head screwdriver to carefully pry off this plastic cover. You can also use a knife for this step.

Once the cover is removed, you will be able to see the screws holding the stand to the monitor. Hold the stand firmly with one hand and use your other hand to unscrew them with a screwdriver. There should be four screws in total.

After removing the screws, you can now separate the stand from the monitor. Be careful not to drop or damage any parts during this process.

Note: This process may vary slightly depending on the exact model of your ASUS monitor.

Use a flathead screwdriver to remove the stand

To remove the stand from your ASUS monitor, you will need a few tools, including a flathead screwdriver. Here is a step-by-step guide on how to do it:

Gather the Necessary Tools:

Before you begin, make sure you have everything you need. In addition to the flathead screwdriver, get a Phillips screwdriver and a soft cloth or towel to protect your monitor's screen. It is crucial to use the correct size and type of screwdriver to avoid damaging the screws or your monitor.

Unplug All Cables:

Start by turning off your monitor and unplugging all cables connected to it. This includes the power cable and any other cables like HDMI or DisplayPort cables. Be gentle when handling the cables, and avoid pulling on them forcefully. Keep them organised as you unplug them so that reassembly is easier.

Adjust the Tilt and Height of the Monitor:

If possible, adjust the tilt and height of your monitor to a comfortable position. This will make the removal process easier and safer. Most monitors have built-in mechanisms for tilt adjustment, and some also have height-adjustable stands.

Locate the Screws or Levers Holding the Stand:

Find the screws or levers that hold the stand in place. These are typically on the back of the monitor, near the bottom or on the sides of the stand. Your monitor may use screws that require a Phillips screwdriver, or it may have levers that can be released by hand or with a flathead screwdriver.

Unscrew or Release the Stand:

If your monitor uses screws, use the appropriate size Phillips screwdriver to rotate each screw counterclockwise and loosen it. Support the monitor with your other hand to prevent it from falling. If your monitor uses levers, gently pry them open or release them using a flathead screwdriver, following the manufacturer's instructions.

Remove the Stand:

Now that the stand is detached, carefully lift the monitor upwards and slide it off the stand. Set the monitor down on a soft and stable surface. Inspect the stand attachment area to ensure no cables or connectors are still attached. If you plan to dispose of the stand, do so responsibly by recycling it or following electronic waste disposal guidelines.

By following these steps, you can safely remove the stand from your ASUS monitor. Remember to consult the manufacturer's instructions if you need more specific guidance for your particular monitor model.

Use a screwdriver to detach the arm/base

To detach the arm/base of your Asus VN279 monitor, you will need to follow a few simple steps. Firstly, place the monitor face down on a table. It is recommended to cover the table surface with a soft cloth to prevent any damage to the screen. Next, remove the rubber coverings from the four screw holes. Once these are removed, you can detach the base of the monitor.

Now, you will need to use a screwdriver. First, pry the rear hinge cover with the screwdriver. Then, use the screwdriver to remove the four screws on the hinge. Be sure to hold the stand while removing the screws. Once these are removed, you will have successfully detached the arm/base of your Asus VN279 monitor.

Frequently asked questions