Removing The Lg5 Camera: A Step-By-Step Guide

how to remove lg5 camera

The LG G5 is a smartphone with a unique slide-out battery and a detachable I/O module, allowing for multiple hardware expansion options. The phone has two rear cameras, one 16MP standard camera and one 8MP wide-angle camera, as well as an 8MP front-facing camera. The rear-facing camera can be replaced by removing the screen, detaching the camera-ribbon connector from the motherboard, and then removing the camera with tweezers.

shundigital

Removing the back cover

To remove the back cover of the LG G5, start by pressing the button on the left side of the phone and sliding it to the left. Then, take out the battery module. Next, separate the bottom module from the battery and remove the SIM card tray.

Now, for the back cover removal: insert a guitar pick (or a similar thin tool) between the back cover and the chassis. Slide the pick along the edge until the back cover comes off. There is a springy mechanical gadget on the back cover that is used to fix the battery in place, so be careful when prying it off.

With the back cover removed, you will expose the motherboard, which is secured to the chassis with six screws. You can now proceed to remove the camera, following the instructions provided on the relevant repair guide.

shundigital

Detaching the screen

To detach the screen of an LG G5, you will need a sim card eject tool, a plastic opening tool, a spudger, and tweezers.

First, while holding the battery release button, pull the bottom end of the phone out of the body. Insert the sim card eject tool into the small hole on the sim card tray and press inward to eject the tray. Pull the sim card tray out of the phone.

Next, remove the two 5.5mm Phillips #00 screws from the base of the phone. Insert the plastic opening tool into the seam between the glass screen and the metal body. Pry the glass from the body a small amount. Insert the spudger into the space between the body and screen and push inward to separate the screen further. Slowly slide the spudger up the edge of the phone until the screen pops out of the body.

When putting the screen back in, press the edges down from the top of the phone to the bottom. The screen should "pop" into place.

shundigital

Disconnecting the motherboard

To disconnect the motherboard of your LG G5, you will need a few tools, including a screwdriver, tweezers, a crowbar, and a guitar pick.

First, press the button on the left side of the phone and slide it to the left to remove the battery module. Next, separate the bottom module from the battery and remove the SIM card tray. Insert the guitar pick between the back cover and chassis, sliding it along until the back cover comes off.

Now, you will need to remove the six screws that secure the motherboard to the chassis. Once these are removed, disconnect the display cable from the motherboard. You can then take out the motherboard.

If you are having trouble removing the motherboard, it may be fixed to the back cover with a springy mechanical gadget, which is used to fix the battery in place.

Alternatively, you can follow the steps outlined in this teardown guide for the LG G5, which includes a step-by-step process with visuals. The guide also provides additional information on the internal components of the phone, which may be useful if you plan to make any other hardware changes.

Additionally, if you are looking to replace the rear-facing camera, this repair guide provides detailed instructions on how to remove and replace the camera module.

Cameras' Vision: Around Trailers

You may want to see also

shundigital

Removing the camera with tweezers

To remove the camera with tweezers, follow these steps:

Firstly, power off your LG G5 device and remove any existing case or cover. You will need to use a plastic case opening tool or a pick to gently pry open the back cover and expose the internal components. This step is crucial to accessing the camera module.

Next, locate the camera lens module, which is usually situated near the top of the phone. Carefully disconnect any ribbon cables or connectors attached to the lens assembly. You may need to use a plastic tool or a pick to gently pry them away. Be cautious not to damage any other components during this process.

Once the ribbons are disconnected, you can now focus on removing the camera with tweezers. Gently lift and separate the camera lens module from its housing, being careful not to touch or damage any surrounding components. Place the removed camera module in a safe location, as you may need to refer to it when installing a new camera.

Now that the old camera is removed, you can prepare for the new camera installation. Clean the housing area with a microfibre cloth to ensure no dust or debris affects the new camera's performance.

Finally, follow the installation steps in reverse to reassemble your device. Ensure all components are securely in place before snapping the back cover back on. Power on your LG G5 and test the camera to ensure optimal performance.

Note: It is advisable to consult a professional or a detailed repair guide for more intricate steps and safety precautions.

Infrared Cameras: 3D Vision Explained

You may want to see also

shundigital

Reassembling the device

To reassemble your LG5 device, follow these steps in reverse order.

Firstly, peel the screen back towards the body of the phone. Press the edges of the screen down, from the top of the phone to the bottom, until you hear a "pop" as the screen clicks back into place.

Next, insert the screen and body back together. Push inward to separate the screen, then slowly slide the nylon spudger down the edge of the phone until the screen pops out of the body.

Now, insert the sim card tray back into the phone, then press inward to secure it in place. Pull the bottom end of the phone out of the body, while still holding the battery release button.

Finally, secure the two 5.5mm Phillips #00 screws back into the base of the phone.

Frequently asked questions

First, you will need to remove the back cover of your phone. Then, remove the SIM card tray and the battery. Next, use a plastic opening tool to pry the screen from the body. Once the screen is removed, you can detach the ribbon connector from the motherboard and use tweezers to carefully lift the camera out.

You will need a sim card eject tool, a plastic opening tool, a spudger, and tweezers.

Yes, the LG5 is designed with modular components that are easily removed and replaced. The camera can be taken out with minimal tools and without having to open the phone.

The LG5 has two rear cameras: a 16MP standard camera and an 8MP wide-angle camera. It also has an 8MP front-facing camera.

To put your device back together, simply follow the disassembly steps in reverse order.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment