Removing Hrv Back Camera Cover: A Step-By-Step Guide

how to remove hrv back camera cover

Removing the back camera cover of a Honda HR-V can be done by following these steps: first, remove the six external screws from the camera using a Phillips #0 screwdriver. Next, carefully loosen the bottom of the back half of the external case from the camera, being mindful not to lose the screws. Open the battery cover located on the bottom right side of the camera and remove the battery. Then, slide a fingernail or plastic spudger into the groove from the bottom to the top right side of the camera. Squeeze the top right corner gently and pry off the external cover. It is normal to hear a cracking sound. Continue pulling the external cover, and it will come off cleanly. Be cautious of the flash capacitor, as it carries an electrical charge that could deliver an unpleasant shock. Finally, carefully pull off the back cover, as parts behind the case may fall out.

shundigital

Removing the six external screws from the camera

Step 1: Gather the necessary tools, including a Phillips #0 screwdriver, which will be used to remove the external screws.

Step 2: Locate the six external screws on the camera. These screws are crucial for holding the camera's external case together.

Step 3: Carefully insert the Phillips #0 screwdriver into the head of the first screw. Ensure that the screwdriver fits securely into the screw head to avoid slipping or damaging the screw.

Step 4: Start unscrewing the first screw by turning the screwdriver counterclockwise. Apply gentle and steady pressure to avoid stripping the screw head or damaging the surrounding components.

Step 5: Repeat the process for the remaining five screws, working your way around the camera. Take your time and ensure each screw is removed completely before moving on to the next one.

Step 6: Once all six screws have been removed, carefully set them aside in a safe place to ensure they are not lost. These screws will be needed again when reassembling the camera.

Step 7: Gently loosen the bottom of the back half of the external case from the camera. This will allow you to access the internal components and continue with the disassembly process.

Remember to work slowly and carefully throughout this process. It is important not to force anything, as this can lead to damage. Always handle the camera with care and be cautious of sensitive components, such as the flash capacitor, which can carry an electrical charge.

shundigital

Loosen the bottom of the back half of the external case

To loosen the bottom of the back half of the external case, you will need to first remove the six external screws from the camera using a Phillips #0 screwdriver. Once the screws have been removed, carefully loosen the bottom of the back half of the external case from the camera. Be cautious not to lose the screws.

The next step is to open the battery cover, which is located on the bottom right side of the camera. Carefully remove the battery. Then, slide your fingernail or a plastic spudger into the groove from the bottom to the top right side of the camera. Gently squeeze the top right corner of the camera and pry off the external cover. It is normal to hear a "cracking" sound during this step. Continue to pull the external cover, and it will come off cleanly.

Be cautious of the flash capacitor as it carries an electrical charge that may give you an unpleasant shock. Carefully pull off the back cover, as parts behind the back of the case might fall out.

shundigital

Open the battery cover and remove the battery

To open the battery cover and remove the battery, follow these steps:

First, locate the battery cover on the bottom right side of the camera. Using your fingernail or a plastic spudger, gently slide it into the groove from the bottom to the top right side of the camera. This will help you to carefully pry off the external cover. It is normal to hear a "cracking" sound during this process. Continue pulling the external cover until it comes off cleanly. Be cautious, as there is a flash capacitor behind the back of the case that carries an electrical charge, which may give you an unpleasant shock if you touch it.

Once the external cover is removed, you will have access to the battery. Carefully remove the battery, being mindful of any other parts that may be loose behind the cover. Now you have successfully opened the battery cover and removed the battery from your HRV back camera.

shundigital

Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera

To remove the back cover of a camera, you will need to carefully slide your fingernail or a plastic spudger into the groove from the bottom to the top right side of the camera. This process requires precision and caution to avoid any damage to the camera or its components.

  • Loosen the External Case: After removing the six external screws from the camera using a Phillips #0 screwdriver, carefully loosen the bottom of the back half of the external case. Be gentle and ensure you don't lose the screws.
  • Remove the Battery: Open the battery cover located on the bottom right side of the camera. Carefully take out the battery.
  • Slide in the Groove: This is where you will use your fingernail or a plastic spudger. Carefully slide it into the groove, starting from the bottom and moving to the top right side of the camera.
  • Pry Off the External Cover: Gently squeeze the top right corner of the camera and begin to pry off the external cover. It is normal to hear a "cracking" sound during this step.
  • Pull Off the Cover: Continue to pull the external cover upwards. It should come off cleanly. Be cautious of the flash capacitor, as it carries an electrical charge that could give you a shock.
  • Remove the Back Cover: Carefully pull off the back cover. Be aware that parts behind the case might fall out, so handle the camera with care.

By following these steps, you will be able to successfully remove the back cover of your camera while minimizing the risk of damage to its components. Remember to work carefully and deliberately, taking your time with each step.

shundigital

Snap the camera back in

To snap the camera back in, you will need to locate the clips that hold the camera in place. These clips may have broken, causing the camera to dangle. If the clips are intact, simply snap the camera back into place, ensuring it is securely attached.

If the clips are broken, you will need to order replacement clips before proceeding. You can find the relevant clips at this link: http://www.hondaautomotiveparts.com...NAVI)&catcgry4=KACVT&catcgry5=REARVIEW+CAMERA. Once you have the replacement clips, take the following steps:

  • Remove the panel where the backup camera sits by unscrewing or unclipping it.
  • Place the new clips into the appropriate slots, ensuring they are securely attached.
  • Reattach the backup camera to the new clips, snapping it firmly into place.
  • Test the camera to ensure it is functioning properly.

By following these steps, you can securely snap the backup camera of your Honda HR-V back in place, ensuring it is functioning correctly and aligned correctly with the guidelines.

Frequently asked questions

To remove the back camera cover of your HRV without breaking it, carefully pull on the inside front edge until it unclips. You can then slide it off.

If your HRV's back camera is dangling, first check if the clips are broken. If they are, you can order new ones online. If not, the camera might have come loose due to the vibration of opening and closing the rear door. Take it to the dealer and they will adjust it back into its original position under warranty.

To remove the back cover of your camera, first, remove the external screws using a Phillips #0 screwdriver. Then, open the battery cover and carefully remove the battery. Next, slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera. Carefully squeeze the top right corner and pry off the external cover. Finally, carefully pull off the back cover.

To pop back the lower bumper cover of your HRV without removing the bumper, apply pressure to the clip itself. If it is not broken, give it a good whack with the palm of your hand.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment