The Fender Passport is a portable audio system that can be used to amplify voices, instruments, and background music. It is a popular choice for singers and bands due to its versatility, connectivity, and convenience. The Fender Passport Venue model has a headphones out and a mono out option, which can be used to connect to powered monitor speakers. The mono out option is designed for connection to a small powered monitor, allowing performers to hear themselves better on stage. To connect a monitor to the Fender Passport Venue, users can utilize the mono out or headphones out jacks, depending on their preferences and equipment setup.
Characteristics | Values |
---|---|
Number of input channels | 7 |
Input types | XLR/1/4" combo jacks, 1/4" jacks, 1/8" jacks |
Output types | 1/4" jacks, 1/8" jack |
Power | 375 watts |
Speaker size | 8" |
Tweeter size | 1.2" |
Power cable | Detachable |
Speaker cables | 2 |
Bluetooth | Yes |
Sub output | Yes |
Mono output | Yes |
What You'll Learn
Connecting a monitor to the 'mono out' jack
Connecting a monitor to the mono out jack of a Fender Passport Venue is a straightforward process. The mono out jack is designed for use with powered monitors, which are speakers that have their own power amplifier built-in. This allows you to connect an additional monitor to your setup and have more control over your sound.
- Ensure that the power switch on the back of the mixer is turned off before proceeding with any connections.
- Identify the mono out jack on your Fender Passport Venue mixer. It is typically labelled as "Mono Out" and is a 1/4-inch TS jack.
- Prepare the cable you will use for the connection. You will need a 1/4-inch TS cable, which is a monaural instrument cable with a line-level signal.
- Connect one end of the 1/4-inch TS cable to the mono out jack on your Fender Passport Venue mixer.
- Connect the other end of the cable to the input jack on your powered monitor speaker.
- Once the connection is secure, you can power on both the mixer and the monitor speaker.
- Adjust the levels and settings on your mixer to achieve the desired sound. You may need to experiment with placement and volume levels to find the optimal setup for your performance.
Remember to always refer to the owner's manual of your specific Fender Passport Venue model for detailed instructions and safety precautions. Additionally, when working with audio equipment, it is important to make sure all connections are secure and proper power procedures are followed to avoid damage to the equipment.
The Ideal Monitor Size Ratio for Your Setup
You may want to see also
Connecting a monitor to the 'headphone out' jack
The Fender Passport Venue has a stereo input channel that enables you to choose between three kinds of stereo input. The inputs are:
- Bluetooth: a wireless stereo audio connection from your phone, computer, or other Bluetooth device.
- L/Mono and Right Input: a pair of 1/4-inch jacks for connecting a pair of monaural cables from a stereo output instrument such as certain keyboards or guitar pedals. Using the L/Mono jack by itself results in a mono channel heard from both speakers.
- Stereo Input: a 1/8-inch TRS stereo jack for accepting input from a stereo source such as a phone’s headphone output or other line-level stereo audio source.
To connect a monitor to the headphone out jack, you will need a 1/8-inch stereo cable. This cable will have a 1/8-inch TRS connector on one end, which will plug into the headphone out jack on the Fender Passport Venue. The other end of the cable will depend on the type of monitor you are using. If you are using a pair of powered speakers, the cable should have two 1/4-inch TS connectors, which will plug into the left and right speaker jacks on the back of the mixer. If you are using a single powered speaker, the cable should have a single 1/4-inch TS connector, which will plug into the Mono Out jack on the back of the mixer.
It is important to note that the headphone out jack on the Fender Passport Venue is for stereo output, so if you are connecting to a mono monitor, you will need to use an adapter or cable that combines the left and right channels into a mono signal. Additionally, make sure that the power switch on the back of the mixer is turned off before connecting or disconnecting any cables.
Once you have made the appropriate connections, you can turn on the power switch on the back of the mixer. The Power light on the bottom of the mixer panel will glow green. If you are using a Bluetooth device as your monitor, press the Bluetooth button on the mixer. When it is flashing blue, go to your device’s Bluetooth settings and select the Fender Passport Venue. When pairing is complete, the Bluetooth button on the mixer will glow solid blue. Turn up the volume on your device and gradually turn up the Volume knob on the mixer’s channel.
Large Monitor, Large Experience: 42-Inch TV as PC Display
You may want to see also
Using a power amp to connect to the Fender mixer
To connect a power amp to the Fender mixer, you will need to use stereo audio cables. The Passport mixer outputs include a powered connection to the included left and right speakers and the headphone outputs. The Event and Venue models also have additional output features.
Firstly, ensure that the power switch on the back of the mixer is turned off before you proceed. Then, connect a cable with a 1/4-inch TS plug to a powered monitor speaker. You can also connect a cable with a 1/4-inch TS plug to a powered subwoofer. If you are using a subwoofer, set its crossover frequency to 120Hz.
When a cable is connected to the Sub Out, the Passport amplifier and speakers will no longer output bass frequencies, so it is important to ensure that the speakers are connected before turning on the mixer. Make sure all volume knobs are turned all the way down and all cable connections are plugged in. This will prevent loud transient sounds or "pops" that can damage the equipment and your hearing.
Now, turn on the power switch on the back of the mixer. The Power light on the bottom of the mixer panel will glow green. For channels where you have connected either a microphone-level signal or a line-level signal, press the Mic/Line button to select the correct source. The button will glow white if Line is selected.
If you are using condenser microphones with the Venue model, engage the Phantom Power button above the four combi jacks. For the line input channels on the Event or Venue models, use the Line/Hi-Z button to select whether the input is for a line-level device or a high-impedance guitar input. The button will glow white to indicate that a preamplifier has been engaged for high-impedance input.
Now, turn up the Master Volume level a little. While at the mixer, ask someone to help you by going around to each microphone and speaking or singing into it. Check the microphone input one channel at a time and gradually turn up that channel's Volume knob. The channel light above it will glow green if a signal is coming in. Turn it up until the light stays green or flickers to yellow. If the light turns red, the input signal is too loud and is causing distortion.
The Venue model has a master Tone control next to the Master Volume knob, affecting the overall tone of the output signal.
Electricity Usage: Monitored by Companies or Not?
You may want to see also
Using a Laney audiohub 4x4 speaker
The Laney Audiohub 4x4 is a versatile and portable PA speaker system, which can be powered by mains or battery. It features a range of input options, including XLR, line, and instrument connections, as well as Bluetooth for wireless streaming.
To connect the Laney Audiohub 4x4 to the Fender Passport Venue, you will need to use the appropriate cables to match the outputs of the Fender with the inputs of the Laney speaker. The Fender Passport Venue has a "mono out" and a "headphones out" option, as well as a "line out" option if you are using the Series 2 model. The Laney Audiohub 4x4 has two types of input connectors: XLR and 1/4" jack.
If you are connecting via the "mono out" or "headphones out" on the Fender, you will need a cable with a 1/4" jack on one end to connect to the Laney speaker. If you are using the "line out" on the Fender Passport Venue Series 2, you may need an adapter or cable with an XLR connection, depending on your setup.
Once you have the correct cables, connecting the two devices is straightforward. Simply follow these steps:
- Ensure that both the Laney Audiohub 4x4 and the Fender Passport Venue are turned off.
- Using the appropriate cable, connect the output of the Fender Passport Venue (either "mono out", "headphones out", or "line out") to one of the input channels on the Laney Audiohub 4x4.
- Power on both devices and adjust the volume and tone settings on the Laney speaker to your desired level.
It is important to make sure that the devices are turned off before connecting or disconnecting any cables to avoid damaging the equipment or harming your hearing.
Additionally, the Laney Audiohub 4x4 has a "link in" and "link out" connector, which allows you to connect multiple Laney Audiohub 4x4 speakers together to expand your setup. This can be useful if you want to increase the volume or coverage of your sound system.
By following these steps, you can easily connect a Laney Audiohub 4x4 speaker to your Fender Passport Venue, providing a versatile and portable sound solution for your performances.
Mounting an ASUS Monitor: A Creative Solution for Hole-less Designs
You may want to see also
Connecting two Peavey speakers
To connect two Peavey speakers, you will need to determine the type of input and output channels you are working with. The Peavey speakers in question are old and require a power amp, as mentioned in the original query.
Firstly, you will need to identify the input and output channels on your mixer. The different input channels on your mixer will have different types of jacks for input from various sources. These can include a combi jack, which can accept a cable with a three-pin XLR plug connection, a 1/4-inch TS jack for a monaural instrument cable with a line-level signal, and a 1/8-inch TRS jack for a stereo cable.
The Peavey speakers will likely use a 1/4-inch TS jack, which is a monaural instrument cable with a line-level signal. This type of jack is commonly used for connecting speakers and amplifiers.
Now, let's determine the correct way to connect the speakers. The speakers can be connected in series or parallel. Connecting the speakers in series means that the cable from the amplifier will split into two, with one split connecting to the positive terminal of one speaker, and the other split connecting to the negative terminal of the other speaker. The speakers are then connected to each other using a smaller cable, typically a white one, that runs directly between the remaining poles.
Connecting the speakers in parallel is another option. This involves connecting the cable from the amplifier to the positive terminal of one speaker, and then connecting the negative terminal of that speaker to the positive terminal of the second speaker. The negative terminal of the second speaker is then connected to the amplifier's negative terminal.
It is important to note that the speakers should be connected with the correct polarity. This can be checked by using a 9-volt battery and touching the positive and negative terminals to the corresponding speaker terminals. If both speaker cones move outward, they are connected correctly.
Additionally, the impedance of the speakers should be considered when connecting them to the amplifier. If the speakers are both 8 ohms, the jack plug on the amplifier should be in the 8-ohm socket for parallel connections or the 16-ohm socket for series connections.
By following these steps, you can successfully connect two Peavey speakers to an amplifier, ensuring correct polarity and impedance matching.
Troubleshooting ASUS Monitor Auto Source Switching
You may want to see also
Frequently asked questions
First, ensure the power switch on the back of the mixer is turned off. Then, connect a cable with a 1/4-inch TS plug to the Mono Out and a powered monitor speaker.
You need a cable with a 1/4-inch TS plug.
The Passport Conference and Event models are set up for input from dynamic microphones using an XLR cable. The Venue model can provide phantom power to condenser microphones on channels 1 through 4. The Venue model also has a second stereo pair channel with the same two wired input options but without Bluetooth.
Yes, you can.