Dismantling A Viewsonic Lcd Monitor: Step-By-Step Guide

how to dismantle viewsonic lcd monitor

If you're looking to dismantle your ViewSonic LCD monitor, there are a few things to keep in mind. Firstly, always remember to unplug the monitor and disconnect all cables before beginning any disassembly process. The process can differ depending on the type of monitor you own, with standard monitors differing from LCD flat screens. For example, the standard monitor uses a base with a sub-base attachment, whereas the LCD flat screen has a base that locks onto a stem at the back of the monitor. It's also important to place the monitor on a soft, flat surface to avoid screen damage. Once you've taken the monitor apart, you'll be able to access the hardware inside and perform any necessary at-home fixes.

Characteristics Values
First Steps Unplug the monitor power cord from the power source. Disconnect the monitor cables from the computer. Place a towel on a flat surface and place the monitor on its side on the towel.
Removing the Base Slide the monitor base forward to access the locking tab on the sub-base. Pull up on the locking tab and slide the sub-base toward the front of the monitor. Remove the sub-base and base away from the monitor.
Disassembling the Monitor Remove the back plastic cover. Remove the four screws connecting the stand. Pull the stand away from the monitor. Insert a thin flat-head screwdriver between the side edges. Slowly pry the case apart as you go around the monitor edges. Lay the monitor face down and pull the back frame away.

shundigital

Unplug the monitor power cord and disconnect monitor cables

To unplug the monitor power cord and disconnect the monitor cables, follow these steps:

Firstly, place a towel on a flat surface. This will serve as a soft, scratch-free area for you to work on. Then, lay the monitor on its side on the towel. This is important, especially for standard monitors with curved screens, as it will prevent damage to the screen.

Now, you can safely unplug the monitor power cord from the power source. Make sure the power is switched off at the outlet before unplugging. Once unplugged, disconnect the monitor cables from the computer. These cables transmit data and power between the monitor and the computer, so it's important to handle them with care to avoid any damage.

If your monitor has a locking tab on the sub-base, you'll need to slide the monitor base forward to access it. The sub-base is located at the bottom of the monitor and connects to the base, which pivots on it. Pull up on the locking tab with your thumb and slide the sub-base towards the front of the monitor. This will release the base, allowing you to remove it.

Finally, place the monitor screen-side down on the towel-covered surface. This will give you access to the locking knob on the bottom of the base. Turn the locking knob counterclockwise by 90 degrees, and then pull the base off the monitor.

shundigital

Place the monitor on a flat surface

To dismantle your ViewSonic LCD monitor, it is important to place the monitor on a flat surface. This is a crucial step to ensure the safety of the device and prevent any accidental damage during the dismantling process. Here are some detailed instructions to follow:

Firstly, choose a suitable flat surface that is stable and secure. A flat table or worktable is ideal, ensuring it is sturdy and capable of bearing the weight of the monitor. Cover the surface with a soft material, such as a towel or foam, to protect the monitor's screen and surface from scratches or other damage. This is especially important if your monitor has a flat screen, as placing it on its side on a soft surface will help avoid screen damage.

Before placing the monitor on the prepared flat surface, make sure there are no objects or obstructions underneath it. This is to ensure that the monitor lies flat and stable, reducing the risk of it toppling over. Once the surface is clear and prepared, carefully lay the monitor on its side on the towel or foam, following the specific instructions for your monitor type.

If your monitor has a curved screen, placing it on its side is recommended to avoid screen damage. For LCD flat screens, ensure that the monitor is locked onto the stem at the back before placing it on the flat surface. This will provide stability and security during the dismantling process.

Additionally, always unplug the monitor's power cord from the power source and disconnect all cables, including the monitor cables from the computer, before placing the monitor on the flat surface. This step is crucial for safety reasons and to prepare for the subsequent dismantling steps.

By carefully following these instructions, you will be able to safely place your ViewSonic LCD monitor on a flat surface, ready for further dismantling or disassembly.

shundigital

Remove the monitor stand

To remove the monitor stand from a ViewSonic LCD monitor, you will first need to unplug the monitor power cord from the power source and disconnect the monitor cables from the computer. Place a towel on a flat surface and lay the monitor on its side on the towel.

Next, slide the monitor base forward to access the locking tab on the sub-base. The sub-base connects to the bottom of the monitor, and the base pivots on the sub-base. Pull up on the locking tab with your thumb, and slide the sub-base toward the front of the monitor. Remove the sub-base and base away from the monitor.

Now, place the monitor screen-side down on a towel over a flat surface. Locate the locking knob on the bottom of the base. Turn the locking knob counterclockwise 90 degrees with your fingers and pull the base off the monitor.

Finally, on the back of the monitor, at the bottom, to the right and left of the "arm" portion of the stand, you will find two screws. Unscrew one screw from each side. Without pulling forward or backward, slide the arm down and out of the slot. A metal bracket from inside the monitor will come out with it. You may need to move the arm slightly from side to side, but not front to back.

shundigital

Remove the back cover

To remove the back cover of a ViewSonic LCD monitor, start by unplugging the monitor power cord from the power source and disconnecting all cables from the monitor. Place the monitor on a flat, stable surface, preferably with a towel to avoid damaging the screen.

The next steps depend on your monitor type. If you own a standard monitor, the base has a sub-base attaching it to the monitor. Slide the monitor base forward to access the locking tab on the sub-base. Pull up on the locking tab with your thumb and slide the sub-base towards the front of the monitor. Remove the sub-base and base away from the monitor.

For an LCD flat-screen monitor, the base locks onto a stem at the back of the monitor. Place the monitor screen-side down on a towel over a flat surface. Locate the locking knob at the bottom of the base and turn it counterclockwise 90 degrees with your fingers. Pull the base off the monitor.

Once you have removed the base, you will see four screws connecting the stand. Remove these screws and pull the stand away from the monitor. Insert a thin flat-head screwdriver between the side edges to slowly pry the case apart. As you go around the monitor edges, you will come across plastic latches that disconnect the frame.

Finally, lay the monitor face down and pull the back frame away to access the back of the monitor.

shundigital

Disassemble the keyboard

To disassemble a keyboard, you will need to first place it upside down on a flat surface and remove the screws from the side using a screwdriver. Once you have removed all the screws, carefully flip the keyboard back over and remove the keys from the top. Place the keys in a bowl of soapy water to soak. Next, remove the screws from the top of the keyboard and set them aside.

Now you can open up the keyboard and dust or clean the inside. When you are done, replace all the parts you removed in the reverse order that you took them out, and plug the keyboard back in.

Frequently asked questions

First, unplug the monitor power cord from the power source and disconnect the monitor cables from the computer. Then, place the monitor on a flat, stable surface, preferably with a cover to protect the LCD panel from scratches. Make sure there are no objects underneath the monitor. Next, press both sides of the hinge cover and pull out the left and right sides. Finally, follow the steps in the user manual to finish disassembling the monitor.

First, remove all the cables attached to the monitor, including the power and signal cables. Then, pull off the back plastic cover where the stand connects to the monitor. This will reveal four screws. Remove these screws and pull the stand away from the monitor.

Use a thin flat-head screwdriver between the side edges of the monitor. You will see a separation line where the front and back halves connect. Slowly pry the case apart as you go around the monitor edges.

Always place the monitor on a flat, stable surface to prevent it from falling and causing damage or injury. Be careful when taking apart computer devices as you can permanently damage the device and break your warranty policy.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment