Disconnecting Your Monitor From The Asus Q551l Laptop

how to disconnect monitor from asus q551l

The Asus Q551L is a 2-in-1 device released in 2014. In this article, we will discuss the steps required to disconnect the monitor from the device. It is important to note that before attempting any repairs or modifications to your device, you should consult a professional or refer to the official product manual for detailed instructions.

shundigital

Unscrew the 10 screws around the back panel

To disconnect the monitor from your Asus Q551L, you'll need to remove the back panel of the laptop. This is how you do it:

First, locate the 10 screws around the edge of the back panel. Eight of these screws are 0.0793mm T5 screws, and two are 0.0793 JIS #0 screws. Using a screwdriver, carefully unscrew all 10 screws. Be sure to keep them in a safe place so you can easily retrieve them when you need to reassemble the device.

Once all the screws are removed, gently pry the back panel away from the base of the laptop using a plastic opening tool. Be careful not to apply too much force, as you don't want to damage the plastic. With the back panel removed, you'll now have access to the internal components of the laptop, including the monitor.

At this point, you can proceed with disconnecting the monitor or performing any other necessary maintenance or repairs. Remember to exercise caution when working with the internal components of your laptop, and always refer to a reliable source for specific instructions on disconnecting and reconnecting the monitor.

When you're finished and have resolved any issues with your Asus Q551L, you can reassemble the device by following the disassembly steps in reverse order. Make sure to securely fasten all the screws and ensure that the back panel is properly aligned and attached before powering on your laptop.

shundigital

Pry the back panel off the base of the laptop

To pry the back panel off the base of the Asus Q551L laptop, you will need to first power down the computer and unplug the power adapter. Then, flip the laptop upside down.

Next, you will need to locate and unscrew all the screws around the edge of the back panel. For the Asus Q551L, there are 10 screws in total: eight of them are 0.0793mm T5, and two are 0.0793 JIS #0.

Once all the screws have been removed, you can start prying the back panel off. You can use a plastic opening tool or a pry tool designed for this purpose. Start by gently prying the removal tab up. You will feel and hear the first clip release, popping up slightly. Then, work your way around the border of the panel, releasing the rest of the clips. Be careful not to damage the plastic or break any of the clips.

Once all the clips have been released, lift the cover up and pull it towards you to fully remove the back panel.

Remember to follow the steps in reverse if you need to reassemble the laptop or put the back panel back on.

shundigital

Unscrew and remove the battery

To disconnect the monitor from an Asus Q551L, you will need to first unscrew and remove the battery. Here is a detailed, step-by-step guide on how to do this:

Step 1: Power Off and Unplug

Before beginning any work on your laptop, ensure that it is powered off and unplugged from any power source. This is an essential safety precaution to prevent any potential damage or accidents.

Step 2: Unscrew the Back Panel

Using a screwdriver, unscrew the 10 screws located around the edge of the back panel. Eight of these screws are 0.0793mm T5, while the remaining two are 0.0793 JIS #0. Once all the screws have been removed, use a plastic opening tool to gently pry the back panel off the base of the laptop.

Step 3: Unscrew and Remove the Battery

Now, we will focus on removing the battery itself. First, unscrew the four screws that secure the battery in place. Then, unclip both wire clips on the upper and right sides of the battery. These clips help to stabilize the battery and provide an electrical connection. Once the screws are removed and the clips are unfastened, carefully lift the battery out of the device.

It is important to handle the battery with care and avoid bending or damaging any wires or components during this process.

Battery Removal Complete

At this point, you have successfully unscrewed and removed the battery from your Asus Q551L. Remember, if you need to reassemble your device, simply follow these steps in reverse order.

shundigital

Lift the battery out of the device

To lift the battery out of the Asus Q551L device, follow these steps:

Firstly, ensure that your device is turned off and unplugged before removing the battery. Start by unscrewing the 10 screws around the edge of the back panel. Eight of these screws are 0.0793mm T5, and the remaining two are 0.0793 JIS #0. Once the screws are removed, use a plastic opening tool to gently pry the back panel off the base of the laptop.

With the back panel removed, you will now have access to the battery. Unscrew the four screws securing the battery in place. After unscrewing, you will need to unclip both wire clips on the upper and right sides of the battery. These wire clips provide an additional layer of security, ensuring the battery remains firmly in place during regular use.

Now, you are ready to lift the battery out of the device. Gently lift the battery out, being careful not to damage any nearby components. It is recommended to use a plastic tool or a similar non-conductive instrument to avoid any potential electrical hazards.

Once the battery is removed, you can proceed with any necessary repairs or replacements. Remember to follow these steps in reverse order to reassemble your device and secure the new or recharged battery.

shundigital

Pry the front edges of the screen off the back

To disconnect the monitor from your Asus Q551L, you will need to pry the front edges of the screen off the back. Here is a detailed, step-by-step guide on how to do this:

Step 1: Before you begin prying, ensure you have the necessary tools. You will need a plastic opening tool, which you can use to gently pry the front edges of the screen away from the back. You can also use other thin, flat tools wrapped in a layer of cloth or tape, such as a flat-head screwdriver or a guitar pick. This will help protect the screen from scratches.

Step 2: Identify the seam that runs along the edges of the screen. This seam is secured by tabs, which you will need to force apart to separate the front and back of the screen.

Step 3: Start prying at one end of the seam. Use your plastic opening tool, or alternative tool, to gently apply leverage and separate the tabs. Be careful not to use excessive force, as this may damage the tabs or dent the plastic.

Step 4: Work your way along the seam, one tab at a time. Continue prying gently and gradually making your way around the entire screen. It is important to be patient and persistent, as you are unlikely to see much progress at first.

Step 5: As you work your way around the screen, use a piece of soft, thin plastic to hold your pry open. This will help keep the tabs separated as you move to the next one.

Step 6: Once you have gone all the way around the screen, the front edges should be completely separated from the back. Now you can move on to the next steps of removing the monitor, such as disconnecting the cables and removing the screen assembly.

Remember to be cautious and gentle throughout the process to avoid damaging any components. If you feel unsure at any point, consider seeking guidance from a professional or referring to detailed disassembly guides or videos for similar models.

Frequently asked questions

Ensure the power is off and the device is disconnected from any power sources before attempting to disconnect the monitor.

Yes, you will need a plastic opening tool and a thin object like a screwdriver to help pry the monitor away from the device.

First, you must remove the back panel by unscrewing the 10 screws around the edge. 8 of these screws are 0.0793mm T5, and the remaining 2 are 0.0793 JIS #0.

You will need to disconnect the battery. Unscrew the 4 screws holding the battery in place and unclip the wire clips on the upper and right side. Then, carefully lift the battery out.

Use a metal spudger to gently lift the two plastic squares off the screen. Then, unscrew the two PH0 screws and use the plastic opening tool to pry the front edges of the screen away from the back. Finally, gently pry the LCD screen away from the front frame.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment