Removing The Asus Tuf Monitor Stand: A Step-By-Step Guide

how to take off asus tuf monitor stand

If you're looking to upgrade your monitor stand or get rid of the old one, you've come to the right place. This article will show you how to take off your Asus monitor stand in a few easy steps. The process is simple and can be done in just a few minutes with a screwdriver. However, if you don't have enough knowledge about the process, you may break the stand, so it's important to follow the correct sequence and be careful throughout.

Characteristics Values
Difficulty Tricky and easy at the same time
Monitor stand components 3: the connector, the vertical stand, and the base
Equipment needed Screwdriver
First step Remove the base
Base shape Rectangular, circular, triangular, or arc
Base attachment Screw or hook
Second step Remove the vertical stand
Vertical stand attachment Screws or a point
Third step Remove the connector or vertical stand holder
Connector attachment Screws

shundigital

Disconnect cables and power

Disconnecting cables and power is the first step in removing your Asus monitor stand. This is important for safety reasons and to ensure that you don't damage your monitor or any of its components.

First, unplug the monitor from its power source. This will ensure that there is no power flowing to the monitor during the removal process. It is important to do this before attempting to remove any cables or stand components.

Next, disconnect all cables and wires connected to the monitor. This includes any power cables, HDMI or display port cables, audio cables, and any other peripheral connections. Be sure to disconnect them carefully and set them aside in a safe place so that they don't get damaged or tangled.

Once all the cables and wires are disconnected, it is a good idea to place the monitor face down on a flat, clean surface. This will give you access to the back of the monitor, where the stand is typically attached. Make sure that the surface is smooth and free of any debris that could scratch or damage the monitor.

At this point, you may also want to press and hold the power button on the front of the monitor for about 10 seconds to discharge any remaining electricity. This is an optional step but is recommended for safety reasons.

Now that you have disconnected the cables and power, you can move on to removing the base and stand from your Asus monitor. Remember to handle the monitor with care and follow the specific instructions for your monitor model to avoid any damage.

shundigital

Remove the base

To remove the base of your Asus monitor stand, follow these steps:

Firstly, unplug the monitor from its power source and disconnect all cables and wires connected to the monitor. Place the monitor face down on a flat, clean surface. Ensure you have a cloth under the monitor to protect it.

Now, locate the screws that attach the base to the monitor stand. These screws are usually hidden under rubber or plastic covers. Use a screwdriver to remove the screws and set them aside safely.

Gently lift the base off the monitor stand. You may need to use a prying tool to do this. Once the base is removed, you can discard it or keep it for spare parts. Be sure to clean any dust or debris that has accumulated under the base.

Finally, reattach the monitor stand to the monitor using the screws you removed earlier. Be careful not to damage the monitor stand or the monitor during this process.

shundigital

Remove the vertical stand

To remove the vertical stand from your Asus monitor, you will need to follow a specific sequence: first the base, then the vertical stand, and finally the connector. The vertical stand is the part of the monitor stand that gives the monitor height.

  • Place your monitor on a surface, preferably with a cloth underneath as a precaution.
  • Look at the bottom surface of the base. You will find either a screw or a hook. If there is a hook, rotate it in an anti-clockwise direction. If there is a screw, use a screwdriver to remove it. Now, remove the base plate from the vertical stand.
  • Check if the vertical stand is connected to the monitor. This is the case for some Asus monitors. If so, you will need to remove the back part of the monitor to access the vertical stand.
  • For example, if you have an Asus MX239 monitor, you will need to remove the base first. Then, you will see two screws on the back of the monitor. Take them off and remove the back cover. Underneath the cover, you will find three screws that attach the vertical stand to the monitor. Use a screwdriver to remove these screws, and then you can take out the vertical stand.
  • For an Asus ROG monitor, first, remove the base. Then, look at the back of the monitor, where you will find a circular plastic cover. Remove this cover with a screwdriver, and you will find four screws underneath. Take these out, and you can then remove the vertical stand.
  • Some vertical stands do not have screws. For these, gently pull the stand down to remove it.

Now that you have removed the vertical stand, you can move on to removing the connector or vertical stand holder.

shundigital

Disconnect the connector

Disconnecting the connector is the final step in removing your Asus monitor stand. The connector is the component that joins the vertical stand to the monitor. To disconnect it, you'll need to remove the back panel of the monitor.

First, remove the screw from the back of the monitor. Then, gently take out the back panel. You should now be able to see some screws that are holding the connector in place. Remove these screws and take out the connector from the back panel of the monitor.

Be sure to handle the monitor with care and follow the manufacturer's instructions for proper disassembly and disposal of electronic devices.

shundigital

Dispose of the stand

Once you have successfully removed the monitor stand, you can dispose of it. However, you should be careful to do so in a responsible manner, as the stand may contain hazardous materials. Be sure to follow your city's regulations for disposing of electronic waste.

If you are replacing the stand with a new one, you can keep the old one for spare parts or recycle it. It is important to separate the monitor and the stand for recycling, as they may have different recycling requirements.

When disposing of the stand, it is also important to handle it with care to avoid injury. The stand may have sharp edges or corners that could cause cuts or scrapes. Be sure to wear protective gear, such as gloves and eye protection, when handling the stand.

Additionally, you should be aware that removing the stand from your monitor may void your warranty. So, it is always a good idea to check with Asus before making any modifications to your monitor.

Finally, if you are unsure about how to properly dispose of the stand, you can always consult a technician or a professional recycling service for assistance. They will be able to guide you on the best way to dispose of the stand in an environmentally friendly manner.

Frequently asked questions

First, make sure the monitor is turned off and unplugged from any power sources. Disconnect all cables and wires connected to the monitor. Place the monitor face down on a flat, clean surface. Use a screwdriver to remove the screws attaching the stand to the monitor. Gently lift the stand away from the monitor.

Unplug the monitor from the power source. Disconnect all cables and wires connected to the monitor. Place the monitor face down on a flat, clean surface. Use a flathead screwdriver to gently pry the base away from the monitor.

First, check if there is a VESA locking screw installed and remove it if there is. Next, release the VESA plate by pressing down on the plastic tab. Remove the monitor cables, lift the monitor from the VESA mount and take it out.

Unplug the monitor from the power source and any other cables that are connected to it. Grasp the monitor firmly with both hands and lift it up off the stand. Be careful not to drop the monitor as this can cause damage. Once the monitor is off the stand, place it in a safe location away from the stand and any other objects.

You will need a screwdriver to remove the screws attaching the stand to the monitor. You may also need a flathead screwdriver or a prying tool to gently pry the stand or base away from the monitor.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment