If you need to take the back off your Asus monitor, it's likely that you'll need to remove the stand first. This may involve prying off a back plate to access the screws holding the stand in place. Once the stand is removed, you'll need to locate and remove any remaining screws. Be careful not to damage the plastic while prying it off. In some cases, you may need to use a thin, stiff prying device to release plastic clips holding the monitor together. It's important to note that disassembling your monitor can be dangerous, especially if it's a CRT model, and may void your warranty. If you're unsure about what you're doing, it may be best to seek professional help or consider buying a new monitor if it's inexpensive.
Characteristics | Values |
---|---|
Before disassembling | Check if there is something broken or not working |
Tools | Metal spudger, screwdriver, flat-head screwdriver, stiff pointed tool, thin cloth, Jimmy |
General tips | Peel stickers to check for screws, look for plastic tabs, check for a seam around the monitor, do not touch the power supply |
Specific tips for VK246 LCD Monitor | Remove the monitor stand, unscrew the screw at the bottom, unclip the front edge of the screen, unscrew the two Philips screws at both sides of the base, remove the sticker and unscrew the screw behind the stand |
Specific tips for VG248 | Lay the monitor face down, remove the four rubber covers with a stiff pointed tool, remove the four 13.4 mm Philips #1 screws, remove the stand, pull straight up on the bezel, grip the bezel through a thin cloth and lift straight up, repeat for all sides, push in on the corner clip on the bottom left, pull up on the lower edge of the bezel, twist the bezel off, lift the LCD out of the rear case |
Specific tips for VH222H | Pry off the back plate to access the screws |
Specific tips for G75 | Get the top tabs in first, work it along towards the right side, push the left side in, snap the bottom part in by pushing down hard on both bottom corners, slide the tabs in and verify they are lined up, push along both edges towards the front end |
What You'll Learn
Removing the stand
To remove the stand from your Asus monitor, you will need to follow a specific sequence: first the base, then the vertical stand, and finally the connector. You will need a screwdriver for this process.
Step 1: Remove the Base
Place your monitor face down on a surface, preferably with a cloth underneath to protect the screen. The base of your monitor can be rectangular, circular, triangular, or an arc, but the removal process is the same for each shape. Look closely at the bottom surface of the base and you will find either a screw or a hook. If there is a hook, rotate it in an anti-clockwise direction to remove it. If there is a screw, use your screwdriver to remove it. Then, gently remove the base plate from the vertical stand.
Step 2: Remove the Vertical Stand
After removing the base, check whether the vertical stand is connected to a point. Some monitors have a vertical stand that is connected to the monitor, in which case you will need to remove the back part of the monitor to access the vertical stand.
For example, the Asus MX239 monitor has a vertical stand that is connected to the monitor. To remove it, first take out the base, then remove the two screws on the back of the monitor and take off the back cover. You will then see three screws that need to be removed to detach the vertical stand.
If you own an Asus ROG monitor, first remove the base and then look at the back of the monitor. You will find a circular plastic cover that can be removed with a screwdriver. Underneath the cover, there will be four screws that need to be taken out before removing the vertical stand.
Another type of vertical stand cannot be removed with screws. For this type, gently pull the stand down to remove it.
Step 3: Remove the Connector or Vertical Stand Holder
To remove the connector or vertical stand holder, you will need to take off the back panel of the monitor. Remove the screw from the back of the monitor, gently take out the back panel, and then remove any screws attaching the connector to the back panel.
Now you have successfully removed your Asus monitor stand.
Monitoring Marijuana Usage: A Comprehensive American Overview
You may want to see also
Unclipping the bezel
To unclip the bezel of an Asus monitor, you will need to first lay the monitor face down on a smooth, clean surface. This is because the display bezel is held to the rear case by plastic clips that can be released by pulling straight up on the bezel.
Next, use a stiff, pointed tool like a metal spudger to pry out the four rubber covers that are hiding the screws in the rear of the monitor. Remove the four 13.4 mm Philips #1 screws that are securing the monitor stand. Then, remove the stand from the display.
Now, you can start to unclip the bezel. It's best to use your fingers for this rather than a prying tool, as this could damage the LCD. Lay a thin cloth over one of the long edges of the display to protect your fingertips and prevent smudging. Grip the side of the bezel through the cloth and lift straight up. A few clips in the centre will pop free. Be careful to pull straight up and not to pry against the display, as pushing down on the display could damage it. Repeat this procedure, moving to the other long side and lifting up on the centre of the bezel.
Now, grip the centre of the final side and lift the bezel away from the rear case. You have now freed the centres of the four sides and can move on to the corners. Each corner is secured by two large clips that can't be freed by just pulling straight up. Using a thin, stiff prying device like a Jimmy, press in against the bottom clip in the lower left corner (beneath the HDMI logo). While pressing the clip in, pull up on the lower edge of the bezel—the entire corner should pop free. Once you've freed one corner, you should be able to gently twist the bezel off, freeing all of the remaining corners.
Asus Frameless Monitors: Speakers or No Speakers?
You may want to see also
Lifting the LCD
Step 1: Prepare the Monitor
Start by laying the monitor face down on a smooth, clean surface. This ensures that the screen is protected and reduces the risk of accidental damage.
Step 2: Remove the Monitor Stand
The stand needs to be removed before proceeding. To do this, pry out the plastic covers on the rear of the monitor with a stiff, pointed tool, such as a metal spudger. These covers hide the screws securing the stand. Once the covers are removed, use a screwdriver to unscrew and detach the stand from the display.
Step 3: Unclip the Front Edge of the Screen
The display bezel is held to the rear case by plastic clips. To release these clips, pull straight up on the bezel with your fingers. Avoid using any prying tools as they can damage the LCD. It is recommended to wear gloves or use a thin cloth to protect your fingertips and prevent smudging on the LCD. Start at the top centre, then move to the sides, and finally, the bottom. Gently pull the plastic edge outwards and then pull it loose.
Step 4: Work on the Sides
Lay the cloth over one of the long edges of the display. Grip the side of the bezel through the cloth and lift straight up. A few clips in the centre will pop free. Repeat this process on the other long side. Move to the final side and grip the centre, lifting the bezel away from the rear case.
Step 5: Tackle the Corners
Each corner of the bezel is secured by two large clips that cannot be freed by simply pulling straight up. Using a thin, stiff prying device, such as a Jimmy, press against the bottom clip in the lower left corner (usually beneath the HDMI logo). While pressing the clip in, pull up on the lower edge of the bezel. The entire corner should pop free. Repeat this process if necessary for the remaining corners.
Step 6: Lift the LCD
Now that all the clips are released, gently twist the bezel to free any remaining corners. Carefully lift the LCD out of the rear case. Be cautious of the row of adjustment buttons attached by a thin ribbon cable. Ensure that you do not damage this cable during the removal process.
With these steps completed, you have successfully lifted the LCD from your ASUS monitor. Remember to handle the LCD with care and take your time during each step to avoid any accidental damage to your display.
Monitoring Employee Internet Usage: Company Surveillance Exposed
You may want to see also
Accessing internal components
To access the internal components of an Asus monitor, you will need to remove the back panel and open the display. Here is a step-by-step guide on how to do this:
Step 1: Prepare Your Workspace
Lay the monitor face down on a smooth, clean surface. This will protect the screen from accidental damage during the disassembly process.
Step 2: Remove the Monitor Stand
- Identify the four rubber covers hiding the screws that secure the monitor stand in place. Use a stiff, pointed tool, such as a metal spudger, to pry out these plastic covers.
- Once the screws are exposed, remove the four screws using a Philips-head screwdriver.
- Detach the monitor stand from the display.
Step 3: Unclip the Front Edge of the Screen
- The display bezel is held to the rear case by plastic clips. To release these clips, pull straight up on the bezel. It is recommended to use your fingers for this step to avoid damaging the LCD.
- Start by pulling on the top centre of the bezel, then move to the sides, and finally, the bottom. Gently pull the plastic edge outwards and then pull it loose.
Step 4: Unscrew the Sides
- On each side of the base, locate and unscrew the two Philips screws.
- Now you can slide the base downwards and remove it completely.
Step 5: Unscrew the Bottom
Behind the stand, at the bottom centre, there is typically a single screw covered by a warranty sticker. Remove the sticker and then unscrew this screw.
Step 6: Lift the LCD Out of the Rear Case
- Be careful with this step as the row of adjustment buttons is attached to the display by a thin ribbon cable.
- With the casing removed, you now have full access to the internal components, including the button board, cables, and the housing over the motherboard components.
Reassembly
To put your monitor back together, simply follow these steps in reverse order. Take care to line up all the clips and screws properly to secure the monitor casing correctly.
Disassembling the Asus VN248 Monitor: Removing the Stand
You may want to see also
Reassembling the monitor
Now that you have disassembled your Asus monitor, it is time to put it back together. Here is a step-by-step guide on how to do it:
Step 1: Place the LCD screen back into the rear case. Be gentle and careful not to damage the LCD.
Step 2: Secure the LCD screen with the four 13.4 mm Philips #1 screws.
Step 3: Reattach the display bezel to the rear case by lining up the plastic clips and gently pushing down. Again, be careful not to use any prying tools that could damage the LCD.
Step 4: Reattach the monitor stand to the display. Secure it with the four screws you removed earlier.
Step 5: Turn the monitor right-side up and place it back on your desk or table.
Step 6: Reconnect all cables and power sources. Make sure that all connections are secure.
Step 7: Power on the monitor and test it to make sure it is functioning properly.
It is important to be gentle and careful during the reassembly process to avoid damaging any of the components. Take your time and refer to your notes and pictures if needed. If you are unsure about any step, it is always best to consult a professional or expert for help.
Additionally, here are some general guidelines for reassembling your Asus device:
- Work in a clean and well-lit space.
- Use small containers or magnets to hold screws and small parts.
- Refer to your notes and pictures to guide you through the reassembly process.
- Take your time and be methodical.
- Do not rush the process and make sure all connections are secure before powering on the device.
Monitoring GPU Memory Usage on Linux: A Comprehensive Guide
You may want to see also
Frequently asked questions
Before disassembling your monitor, ensure that you have a valid reason to do so, as it may void your warranty. If you are certain, begin by laying the monitor face down on a smooth, clean surface. Next, remove the monitor stand by prying off the back plate to access the screws. Then, remove the four rubber covers hiding the screws in the rear of the monitor using a stiff, pointed tool, such as a metal spudger. Finally, remove the screws securing the stand and carefully lift the bezel away from the rear case.
To remove the stand from your Asus monitor, first put the monitor face down. Then, look at the side of the stand and locate the indent near the top. Use a flathead screwdriver to wedge into the indent and gently pry off the top part. Once the plastic panel is removed, you will be able to access the screws holding the remainder of the stand in place.
Yes, there are several online resources that can provide guidance on disassembling an Asus monitor. Try searching for your specific model on websites such as iFixit, YouTube, or Reddit. These platforms often feature step-by-step guides and video tutorials created by other users who have successfully disassembled similar monitors.