Removing Cpi Doorbell Cameras: A Step-By-Step Guide

CPI doorbell cameras are a great way to monitor your front door and keep your home secure. However, there may be times when you need to remove the camera, such as when you're moving to a new house or upgrading to a new model. In this case, you'll need to know how to safely and properly remove the camera without causing any damage. This can be a tricky process, as demonstrated by a user on Reddit who was unable to remove the backplate of their CPI doorbell camera despite successfully popping off the front part. Luckily, other users were able to provide advice and guidance on how to remove the camera, which we will cover in this article.

Pop off the front part of the camera

To remove a CPI doorbell camera, you can start by popping off the front part of the camera. This is a relatively straightforward process, but it requires some care to avoid damage. Here are the steps you can follow:

• Locate the white circles on the camera's front part: These are caps covering the screws that secure the camera in place.
• Remove the caps: Gently pop off the white circles using your fingernail or a small tool like a screwdriver. Be careful not to apply too much force, as you don't want to scratch or damage the camera or its housing.
• Expose the screws: Once the caps are removed, you will see the screws underneath. These screws hold the backplate of the camera in place.
• Prepare your tools: Gather a small flat-head screwdriver and any other necessary tools. You may also need a larger screwdriver or a drill if the screws are tight.
• Loosen the screws: Using the flat-head screwdriver, carefully insert it into the screw head and turn it counterclockwise to loosen the screws. Be gentle to avoid stripping the screws or damaging the surrounding housing.
• Detach the front part: After loosening the screws, you should be able to carefully pull or pop off the front part of the camera. Again, be cautious to avoid applying excessive force that could damage the camera or its housing.

By following these steps, you will be able to successfully pop off the front part of the CPI doorbell camera, allowing you to access the rest of the camera for further removal if needed. Remember to handle the camera with care and be mindful of any wires or other components that may be attached.

Remove the small white screw caps

To remove the small white screw caps, you will need to pop them off. This will expose the screws that are holding the backplate in place. Once you have removed the caps, you will be able to see the screws and can then proceed to release the backplate.

The small white screw caps act as covers for the screws that secure the backplate of the CPI doorbell camera. They are designed to be removable, allowing access to the screws underneath. By popping them off, you will gain access to the screws and can then proceed to remove the backplate.

It is important to note that these white screw caps are typically quite small and may require a gentle touch to remove them without causing damage. They are often referred to as "little white circles" and can be found on the CPI doorbell camera's housing attached to the house.

Once you have successfully popped off the white screw caps, you will see the screws that need to be removed to release the backplate. Make sure you have a screwdriver that fits these screws securely before proceeding.

Unscrew the backplate

Unscrewing the backplate of a CPI doorbell camera can be a delicate task, but with the right approach, it can be done efficiently and safely. Here's a step-by-step guide to help you through the process:

Locate the Screws: Begin by examining the CPI doorbell camera closely. You will notice that there are small white circles on the device, which are caps covering the screws that secure the backplate in place.

Remove the Caps: Using a small flat-head screwdriver, carefully pop off these white caps. Gently insert the screwdriver under the edge of each cap and pry it up. Be cautious not to apply too much force, as you don't want to damage the caps or the surrounding housing.

Expose the Screws: Once the caps are removed, you will see the screws underneath. There should be at least two screws, and possibly more, depending on the model of your CPI doorbell camera. These screws are what hold the backplate securely to the wall.

Prepare for Unscrewing: Before you start unscrewing, make sure you have the necessary tools ready. You will need a screwdriver that fits the type of screws used in your CPI doorbell camera. It could be a Phillips-head or a flat-head screwdriver, depending on the screw type.

Remove the Backplate: As you unscrew the last screw, the backplate should become loose and can now be carefully removed. Gently pull the backplate away from the wall, being mindful of any wires that may be connected to the doorbell camera. Ensure you detach the backplate completely from the device and any mounting hardware.

By following these steps, you can successfully unscrew and remove the backplate of your CPI doorbell camera. Remember to handle the device with care and be cautious not to apply excessive force, as this could damage the camera or its housing. Always use the appropriate tools and take your time during the process to ensure a safe and effective removal.

Remove the device from your Alarm.com account

To remove the CPI doorbell camera device from your Alarm.com account, you will need to follow these steps:

• Log into your Alarm.com account through the Alarm.com app or the Alarm.com customer website.
• Find the Manage Devices page. On the app, tap on the desired device and follow the on-screen prompts to remove it. On the website, click on "Manage Devices", find the device, and then click "Remove Device" and follow the on-screen prompts.
• Alternatively, you can go to the Users tab on the website, edit the push devices, and remove the doorbell camera that way.
• If you are removing a Z-Wave device that is no longer communicating, you may need to contact your service provider for assistance.
• Note that the options available to you may depend on the permissions set by your service provider. If you cannot find the option to remove a device, you may not have the required permissions.

Reuse the camera by signing up for an alarm.com service

If you want to reuse your CPI doorbell camera, you can sign up for an alarm.com service. This will allow you to continue using the camera without having to install a new one.

To do this, you will need to remove the CPI doorbell camera from its housing. Start by popping off the front part of the camera. Then, use a small flat-head screwdriver to remove the backplate by unscrewing the four black screws holding it in place. Be careful not to use too much force as this may damage the camera.

Once you have removed the camera, you can sign up for an alarm.com service that is compatible with CPI doorbell cameras. One option is to purchase the Essentials Pro Home Security Package from CPI Security, which includes 24/7 alarm monitoring, a smartphone app for remote control, and free professional installation. With this package, you can reuse your CPI doorbell camera and take advantage of its features, such as AI-powered motion detection, two-way audio, and real-time alerts.

By signing up for an alarm.com service, you can continue to use your CPI doorbell camera to monitor your front door, receive alerts, and communicate with visitors. This option can save you the hassle of installing a completely new doorbell camera system and allow you to get the most out of your existing CPI camera.

Frequently asked questions