Removing Acer Monitor Cover: A Step-By-Step Guide

If you want to remove the back cover of your Acer monitor, you'll need to be careful not to damage the monitor or its components. Before you begin, make sure you have a Philips screwdriver and a pry tool, and place the monitor face down on a soft, flat surface to avoid scratching or damaging the screen. You'll then need to remove the screws holding the monitor stand in place, before removing the stand itself. Next, remove the screws securing the back cover to the monitor, and carefully pry the cover away from the monitor.

Place the monitor on a soft, flat surface

To remove the back cover of an Acer monitor, you will need to place the monitor on a soft, flat surface. This is an important step to ensure that you don't damage the monitor during the process of removing the cover.

Choose a work area that is clean, dust-free, and spacious enough for you to work comfortably. A soft surface, such as a table covered with a blanket or a large towel, is ideal. This will provide a cushion for the monitor and protect it from any potential scratches or damage.

Make sure the surface is flat and even to prevent the monitor from rolling or tilting during the process. Place the monitor on the soft, flat surface with the screen side facing down. This will give you access to the back panel and allow you to work on removing the cover without putting any pressure or weight on the delicate screen.

Once the monitor is in the correct position, you can start the process of removing the back cover by following the specific instructions for your Acer monitor model. This may involve removing screws, prying off the cover, or other steps unique to your model. Remember to be gentle and cautious throughout the process to avoid damaging any internal components or the exterior casing.

By taking the time to prepare a suitable work area and carefully placing the monitor on a soft, flat surface, you can help ensure a smooth and safe process for removing the Acer monitor cover.

Remove the memory module

To remove the memory module of an Acer All-In-One Computer model Z1801, follow these steps:

Firstly, ensure that the computer is switched off and unplugged, with all cables disconnected. It is important to ensure the computer is cool before proceeding. Place the device on a soft cloth or protective mat, with the screen facing downwards.

Now, locate the memory module slot cover on the underside of the computer. Carefully remove the screw that holds the cover over the memory compartment. Place the screw somewhere safe, perhaps using a piece of tape to secure it to the desktop or the side of the computer.

Next, ground yourself by touching any grounded metal surface, such as a light stand, or the centre screw on an electrical outlet.

Carefully release the latches on the side of the module holder. Lift the module holder to an approximate 30-degree angle from the bottom surface of the laptop.

Finally, gently slide the memory module out of its connector and out of the slot.

You can now install a new memory module. When you are done, simply follow these steps in reverse to reassemble the device.

Detach the stand

To detach the stand from an Acer monitor, you will need to first prepare the surface and the monitor to avoid damaging it or scratching it in the process. Turn the power off and unplug all cables from the monitor. Place a soft cloth, such as a towel or blanket, on a flat surface to protect the monitor from damage.

Now you are ready to detach the stand. For some models, there is a release button close to where the base and monitor connect. For other models, you will need to remove the base, then look inside the tower piece for three Phillips-head screws. Remove these with a screwdriver and the tower piece will come off, leaving a small hinge piece.

To remove the hinge piece, you will need two flathead screwdrivers. Push down the plastic tab in the middle with one screwdriver, and with the other, wedge between the plate and the monitor to get it to move off the plastic tab. The mounting piece will then come off.

For other models, you will need to lay the monitor face down on a stable surface. Ensure that the base is unlocked from the monitor stand arm. You may need to check underneath for a screw that a coin would fit into, and loosen it to disassemble the hinge.

Finally, some models require you to remove the bottom panel completely to unscrew the stand. This panel is secured with small plastic pieces that can break easily, so be careful.

Remove the screws

To remove the screws from your Acer monitor, you will need a Philips-head screwdriver. Before you begin, make sure you have enough space to work in, and lay the monitor face-down on a soft, flat surface to prevent scratches or pressure damage to the screen.

Now you can begin to remove the screws. First, remove the plastic covering the screws for the stand. Then, remove the screws securing the stand. You can then remove the stand by pulling it up and away from the monitor.

Next, remove the screws for the left and right foot stands. You can then remove the stands by sliding them down and out of the monitor.

Finally, remove the screws from the left and right sides of the LCD panel.

Pry loose the bezel

To pry loose the bezel of your Acer monitor, you will need to first lay the monitor facedown on a flat surface. Then, using a flathead screwdriver, work your way around the monitor, inserting the screwdriver into the space between the front and back covers. You should be prying at the locations with little gaps, which are the locking mechanisms.

Be cautious and avoid twisting the screwdriver too much, as this can damage the plastic without achieving the desired outcome. Instead, focus on prying at the right locations, and you should hear a popping sound, indicating that the back cover is lifting.

The locking mechanism locations are on the right, left, and bottom sides of the monitor. Be careful not to pry on the monitor buttons located at the bottom.

Once you have successfully pried loose the bezel, you can then remove the screws from the left and right sides of the LCD panel and slowly lift the panel.

Frequently asked questions