Opening An Asus Monitor: Back Panel Access Guide

how to oprn the back of my asus monitor

If you're looking to open the back of your Asus monitor, you'll need to be careful and methodical. First, lay the monitor face down on a smooth, clean surface. You'll then need to remove the stand and any screws, before carefully prying the back away from the display. It's important to be cautious and patient throughout this process, as you don't want to damage any of the monitor's components.

Characteristics Values
Monitor model ASUS VK246 LCD Monitor
Problem Stuck physical button
Steps to open the monitor 1. Remove the monitor stand. 2. Unscrew the screw at the bottom. 3. Unclip the front edge of the screen. 4. Remove the monitor stand. 5. Unscrew the two Philips screws at both sides of the base. Slide the base down to remove it. 6. Unscrew the screw at the bottom. 7. Pull on the edge of the screen to unclip it.

shundigital

Remove the monitor stand

To remove the monitor stand from your Asus monitor, follow these steps:

Disconnect all cables and power sources:

Before you begin, ensure that your monitor is switched off and unplugged from the power source. Disconnect all cables connected to the monitor, including the power cable, HDMI, DisplayPort, or any other peripheral connections.

Prepare your workspace:

Lay the monitor face down on a smooth, clean, and soft surface to protect the screen from scratches. A blanket or a thick towel can be used for this purpose.

Remove the base:

The base is the first component of the stand that you will remove. The base is the surface of the stand that provides stability when the monitor is placed on a solid surface. It can be shaped like a circle, rectangle, triangle, or arc, but the removal process remains the same.

To remove the base, locate the screw that holds it in place. Some monitors may have a hook that you can rotate in an anti-clockwise direction to remove the screw. Use a screwdriver to gently remove the screw if there is no hook. Once the screw is removed, carefully detach the base plate from the vertical stand.

Remove the vertical stand:

The vertical stand is the upright part of the monitor stand that connects to the base. After removing the base, check if the vertical stand is directly connected to the monitor or if it connects to a holder that comes out of the back of the monitor.

If the vertical stand is directly connected to the monitor, look for any screws holding it in place and remove them. If there are no screws, check for any buttons near or on the vertical stand. Some monitors, like Dell and Acer, have a dedicated button that you need to press to remove the stand. Press the button and gently pull the stand outwards. If it doesn't come out easily, a small amount of mechanical oil can be applied to the joints to help loosen it.

If your monitor has a separate vertical stand holder, you may need to remove the back panel of the monitor to access it. Refer to the user manual to understand how the stand is connected to your specific monitor model.

Remove the connector or vertical stand holder:

The connector is the component that attaches the stand to the monitor. To remove it, you will need to unscrew and remove the back panel of the monitor. Once the back panel is removed, locate any screws connecting the vertical stand holder and remove them. Finally, connect all the cables and reassemble the monitor.

Remember to keep track of all the screws you remove and store them safely for future use. If you encounter any difficulties or feel uncomfortable with the process, consider seeking professional assistance to prevent potential damage to your monitor.

shundigital

Unscrew the screw at the bottom

Unscrewing the screw at the bottom of your ASUS monitor is a crucial step in accessing and repairing its internal components. Here is a detailed guide on how to do this:

Prepare Your Workspace:

Before you begin, ensure you have a clear, dry, and clean flat surface to work on. Avoid using a kitchen or coffee table. Make sure you have proper lighting for a focused workspace. It is also recommended to have small containers or magnets to hold screws and other small parts, a notebook or device for taking notes, and a camera to take pictures as you work.

Locate the Screw:

The screw at the bottom of your ASUS monitor is typically found behind the stand, in the bottom center. It is often covered with a warranty sticker that you will need to remove carefully.

Unscrew the Screw:

Once you have located the screw, use the appropriate screwdriver to carefully unscrew it. In some ASUS models, this may be a Philips-head screw. After removing the screw, keep it in a safe place, as you will need it again when reassembling your monitor.

Proceed with Caution:

After removing the screw, be cautious when attempting to remove the back cover of the monitor. In some models, there may be plastic clips or latches holding the cover in place. You may need to gently pry or pull the cover to release it. Always refer to the specific instructions for your ASUS monitor model to avoid damaging any internal components.

Additional Tips:

When disassembling your ASUS monitor, it is important to keep track of all screws and parts removed. You can use tape to hold screws in place or keep them in a container, labeling them accordingly. Taking pictures and notes at each step can also help ensure a smooth reassembly process.

By carefully following these steps, you will be able to successfully unscrew the screw at the bottom of your ASUS monitor and proceed with any necessary repairs or maintenance. Remember to refer to official ASUS resources or seek professional assistance if you encounter any difficulties during the process.

Monitoring Snapchat: A Guide for Parents

You may want to see also

shundigital

Unclip the front edge of the screen

To unclip the front edge of the screen, start by placing the monitor face down on a smooth, clean surface. Cover the edges of the monitor with a thin cloth to protect the screen and your fingertips. This will also prevent smudging the LCD.

Now, grip the centre of the bezel through the cloth and lift it straight up and away from the rear case. Start at the top centre, then move to the sides, and finish at the bottom. You should be able to pull the plastic edge a little bit to the outside and then pull it loose. It's important to only use your hands for this step, as using a screwdriver may damage the plastic and clips.

If you meet resistance, try to identify if there are any plastic clips holding the bezel in place. These can be released by pulling straight up on the bezel. You can also try gently twisting the bezel to free the corners.

Monitoring RAM Usage: MacBook Pro Tips

You may want to see also

shundigital

Remove the Philips screws at the base

To remove the Philips screws at the base of your Asus monitor, you will first need to lay the monitor face down on a smooth, clean surface. This will give you access to the rear of the monitor, where the screws are located.

Next, you will need to locate and remove the four rubber covers that are hiding the screws. You can do this by prying them out with a stiff, pointed tool, such as a metal spudger. Be careful not to lose these rubber covers, as they are important for protecting the screws.

Once the covers are removed, you will see the Philips screws. Use a Philips-head screwdriver to carefully unscrew them. Make sure to keep track of the screws, as you will need to put them back in when you are finished. Place them in a small container or on a magnet to avoid losing them.

With the screws removed, you can now separate the monitor stand from the display. Gently pull the stand away from the display, being careful not to damage any of the connecting parts.

Now that the stand is removed, you can move on to the next step of opening your Asus monitor. Remember to keep the screws and rubber covers in a safe place so that you can reassemble your monitor when needed.

shundigital

Pry out the plastic covers

To open the back of your Asus monitor, you'll first need to lay the monitor face down on a smooth, clean surface. There are four rubbery covers hiding screws in the rear of the monitor. You can use a stiff, pointed tool, such as a metal spudger, to pry out these plastic covers. Be careful not to use too much force, as you could damage the plastic.

Once you have pried out the plastic covers, you can remove the four screws securing the monitor stand. The stand can then be removed from the display.

The display bezel is held to the rear case by plastic clips. To remove it, pull straight up on the bezel with your fingers or a thin cloth. This will prevent you from damaging the LCD and smudging the screen.

Repeat this process around all four sides of the display, starting with the long edges, then moving to the centre of each side, and finally, the corners. You may need to use a thin, stiff prying device, such as a Jimmy, to press in against the bottom clip in the lower-left corner while pulling up on the lower edge of the bezel.

By following these steps, you should be able to successfully pry out the plastic covers and open the back of your Asus monitor.

Frequently asked questions

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment