Charging The Polaroid Snap Touch: A Step-By-Step Guide

The Polaroid Snap Touch camera is a fun and easy-to-use instant digital camera. If you're having trouble turning on your device, it may be due to a dead battery. To charge your camera, simply plug the cable into a 1-amp charge block and then into your camera. Ensure that the camera is placed flat on the ground and the cable is not fully extended. Once it's charging, you'll see a red LED light, and when it's fully charged, the light will turn white. If your camera is not turning on even after charging, there might be an issue with the viewfinder or internal damage, so you may need to contact Polaroid support for further assistance.

Charging cable options

There are a variety of charging cable options for the Polaroid Snap Touch camera. The camera uses a micro USB to USB (2.0) Data Cable for charging. The official Polaroid Snap Touch USB Cable is 3' in length.

There are also a number of third-party options available, including:

• A 10ft charger cord that is compatible with a range of instant cameras and photo printers, including the Polaroid Zip and Polaroid Mint.
• A T POWER 9V A Charger for the Polaroid Instant Print Digital Camera.
• A USB charge cable cord wire for the Polaroid Zip, HP Sprocket, Polaroid Mint, Kodak Mini/Printomatic, Lifeprint, Canon Ivy, and similar wireless photo printers.
• A USB DC Charger + Data Cable Cord for the Polaroid Snap.
• A BoxWave Wall Charger Direct (5W) for the Polaroid OneStep 2.
• A Micro USB Data/Charger Cable for the Polaroid Zip, Mint, Cube+, Cube, Lifestyle, and Snap.

Charging cable connection

To charge your Polaroid Snap Touch camera, you will need a charging cable that is compatible with your camera. You can find a suitable cable on Amazon, with options including:

• USB Cable Cord for Polaroid Snap Touch Instant Digital Camera
• Polaroid Snap Touch Instant Digital Camera USB Cable 3' MicroUSB to USB (2.0) Data Cable
• USB DC Charger+Data Cable Cord for Polaroid Snap Pol SP01 W SP01PR SP01BL Camera
• Micro USB Data/Charger Cable for Polaroid Zip, Mint, Cube+, Cube, Lifestyle, Snap

Once you have obtained a compatible charging cable, follow these steps to charge your camera:

• Plug the cable into a 1-amp charge block and then into your camera.
• Ensure that the camera is laid flat on the ground and that the cable is not fully extended.
• Allow the camera to charge until the LED light turns white. If a red LED flashes while charging, your battery might need to be replaced.

It is important to note that you should only use the provided charging cable or a compatible replacement to charge your Polaroid Snap Touch camera. Using an incompatible cable may damage your camera or cause it to malfunction. Additionally, always make sure that the camera is turned off before connecting or disconnecting the charging cable.

Charging time

The Polaroid Snap Touch camera should be charged by plugging the cable into a 1amp charge block and then into the camera. The camera should be laid flat on the ground and the cable should not be fully extended.

The charging time for the camera is not specified, but the user manual does specify that the camera is ready to use when the LED light turns white and a chime sounds. If the battery is completely dead, it may take a few hours to charge fully.

If the camera is not turning on, the battery may be dead and need replacing. This can be checked by plugging the camera into the power cable and charging until a white LED light appears. If a red LED light does not flash while charging, then the battery likely needs to be replaced.

If the camera has been left for a long time without being charged, it may just be in sleep mode. In this case, it is recommended to turn the camera on and off again for it to start working.

If the camera has been left without charge for an extended period, the battery may be dead, and the camera will need to be charged before use.

Charging location

To charge your Polaroid Snap Touch camera, you must first plug the cable into a 1amp charge block. Then, plug the other end of the cable into your camera. It is important that the camera is laid flat on the ground and that the cable is not fully extended.

The charging cable required is a USB to micro USB cable. This cable is included with the camera. If you need a replacement, you can find one online.

It is important to note that you should not overcharge your camera. Over time, this can reduce the battery's capacity.

Charging issues

If your Polaroid Snap Touch camera is not turning on, it could be due to a variety of reasons. Here are some steps you can take to troubleshoot charging issues:

• Check if the camera is properly connected to a power source using the provided charging cable. Ensure that the cable is securely plugged into the camera and the power outlet or adapter.
• Inspect the charging cable for any signs of damage, such as frayed wires or broken connectors. Try using a different cable if possible to see if that resolves the issue.
• If the camera has not been used for an extended period, the battery may be deeply discharged. In this case, leave the camera connected to the charger for a few hours before attempting to turn it on again.
• If the camera still does not turn on, try resetting it. Locate the reset button, usually a small hole or recessed button, and use a thin object like a paper clip or toothpick to gently press and hold the reset button for a few seconds.
• Check the viewfinder to ensure it is functioning properly. The viewfinder should pop up when pressed. If it is stuck, carefully use a pen or small object to flick the power switch on.
• If the camera was purchased from a store, it may have been a display model that was constantly plugged in, which could have damaged the battery. Contact the store for assistance or a replacement.
• If the camera was exposed to water, heat, or physical damage, it may have suffered internal damage. In this case, contact Polaroid's customer support for further assistance.
• Ensure that you are using the correct charger for your Polaroid Snap Touch camera. The camera uses a Micro-USB connector for charging.
• If the camera turns on but does not charge, there may be an issue with the battery. Try replacing the battery with a new one to see if that resolves the issue.
• If all else fails, connect the camera to a computer via the charging cable. Turn on the camera while it is plugged into the computer, and if the MSDC screen appears, delete all photos to free up memory. Then, safely remove the device from the computer and turn it off before unplugging it.

Frequently asked questions