Lcd Monitor: Does Nikon 3500 Have One?

The Nikon D3500 is an entry-level 24.2-megapixel DX format DSLR Nikon F-mount camera. It was revealed to the public in August 2018 and initially launched in the United States at a price of $429. The rear LCD screen of the Nikon D3500 has a resolution of 921,000 dots and measures 3.0 inches across its diagonal. While the screen is not touch-sensitive, it occupies a large part of the backside of the camera.

How to turn on the LCD monitor

The Nikon D3500 does have an LCD monitor. The rear LCD screen measures 3.0 inches across its diagonal and has a resolution of 921,000 dots.

• Power on the Nikon D3500 by pressing the power button, which is located on the top right of the camera.
• Familiarize yourself with the camera's controls. The LCD monitor will automatically turn on when you power on the camera, displaying various shooting information such as shutter speed, aperture, and the number of exposures remaining.
• To view additional information on the LCD monitor, press the "R" button. This button is typically located on the back of the camera, near the LCD screen. Pressing the "R" button cycles through different display options, allowing you to see more details about your current camera settings.
• If the LCD monitor does not turn on automatically, ensure that you have not accidentally disabled the "Live View" feature. The "Live View" toggle is located on the top of the camera, at the base of the shooting mode dial. Pull the lever towards you to activate "Live View."
• Adjust the auto-off timer settings to control how long the LCD monitor stays on before turning off automatically. By default, the auto-off timer may be set to a shorter duration. To change this, press the "Menu" button, usually located near the LCD screen, and navigate to the "Auto Off Timers" setting. Here, you can select "Long" or "Custom" to increase the duration before the LCD monitor turns off.
• If the LCD monitor still does not turn on, try a factory reset. You can refer to the camera's manual for detailed instructions on performing a factory reset.

By following these steps, you should be able to successfully turn on and utilize the LCD monitor on your Nikon D3500 camera.

Adjusting the LCD monitor's brightness

The Nikon Coolpix 3500 is equipped with a 1.5-inch colour LCD monitor for composing images. The monitor's brightness can be adjusted in the Setup Menu under Camera Setup. Here, you can choose higher values for increased brightness and lower values for reduced brightness.

The brightness of the monitor can also be adjusted through the Exposure Compensation feature. This feature allows you to produce a brighter or darker exposure on your next shot, without changing the aperture or shutter speed. The Exposure Compensation settings are stated in terms of EV numbers, with possible values ranging from EV +5.0 to EV -5.0. Each full number on the EV scale represents an exposure shift of one stop.

To adjust the Exposure Compensation setting, you can either press and hold the Exposure Compensation button while rotating the Command dial or use the control strip by pressing the "i" button.

Troubleshooting an unresponsive LCD monitor

The Nikon D3500 is a digital camera that comes with an LCD monitor. Troubleshooting an unresponsive LCD monitor can be done in a few ways:

• Try removing the batteries and leaving the camera on a shelf for a few hours or overnight. Then, put the batteries back in and try turning the camera on again.
• Clean the terminals in the battery compartment by rubbing them with a pencil eraser and then wiping them with cotton swabs dipped in rubbing alcohol. Let the camera dry for a few minutes before turning it on again.
• If the camera has been dropped, the impact could have damaged the delicate connections inside, including those to the screen. In this case, the camera may need to be sent for repair.
• Check if the camera is in Live View mode. If it is, exit this mode and try turning on the camera again.
• Perform a factory reset.
• If none of the above solutions work, contact a Nikon-authorized service representative or send the camera to Nikon for repair.

How to extend the LCD monitor's timer

The Nikon D3500 camera features an LCD monitor, which is used for composing images. By default, the monitor turns off after 10 minutes, but this can be adjusted to a minimum of 5 minutes or a maximum of 30 minutes.

To extend the timer for the LCD monitor on the Nikon D3500, follow these steps:

• Turn on your Nikon D3500 camera.
• Press the "Menu" button at the back of the camera, near the LCD screen.
• Navigate to the "Setup Menu" by scrolling through the available options using the left and right buttons.
• Within the Setup Menu, look for the Self-Timer Option or Auto Off Timers setting. This setting controls the duration of the timer for the LCD monitor.
• Adjust the timer duration to your desired length by selecting one of the available options: short, normal, long, or custom.

By following these steps, you can extend the timer for the LCD monitor on your Nikon D3500 camera, allowing the screen to stay on for a longer period before turning off automatically.

Additionally, if you are specifically looking to extend the image review time on the LCD screen, you can adjust the Playback setting, which controls how long an image is displayed after it is captured. This can be set to various durations, such as 2 seconds, 4 seconds, 10 seconds, 20 seconds, or longer, depending on your preference.

How to turn off the LCD monitor

The Nikon Coolpix 3500 does have an LCD monitor, which is used for composing images. However, there does not appear to be a way to turn off the LCD monitor. Instead, the monitor turns off automatically after a few seconds of inactivity.

If you would like to adjust the length of time before the LCD monitor turns off, you can do so by adjusting the 'Auto Off Timers' setting. Here is a step-by-step guide:

How to Adjust the Auto Off Timers on the Nikon 3500:

• Turn on your Nikon 3500 and press the menu button at the back, near the LCD screen.
• Press the left button to navigate to the left side of the screen.
• Select the pencil icon by pressing the up or down buttons. You will know you are on the correct icon when the top of the LCD screen says 'Custom Setting Menu'.
• Press the right button to navigate to the right side of the screen.
• Use the up and down buttons to choose 'Auto Off Timers'. You may need to scroll down through a few screens to find this option.
• Press the OK button.
• Use the up and down buttons to choose your desired timer setting: Short, Normal, Long, or Custom. 'Long' will keep the LCD display on for around 20 seconds before it turns off. 'Custom' lets you set the timer separately for playback settings, image review, and auto meter off.
• Press the OK button to confirm your selection.
• Press the menu button twice to exit the Custom Setting Menu.

By following these steps, you can adjust the length of time the LCD monitor stays on before turning off.

Frequently asked questions