Replacing Batteries In Your Wgi Innovation Nano Camera

The WGI Innovations I8 Game Trail Camera is a robust and classy camera that delivers great results. However, like most electronic devices, it may sometimes encounter certain issues that require fixing. If the problems persist and cannot be resolved, you will need to reset the camera to its factory settings. To replace the batteries, follow these steps:

First, open the door at the bottom of the camera by unlatching the cover. With the camera facing up, open the battery compartment cover by sliding the latch to the left. Next, load the batteries, ensuring that the positive ends of two C-cell batteries are facing towards you in the left battery chamber, and the negative ends are in the right battery chamber. Do not mix old and new batteries, and only use alkaline batteries. Close the battery compartment cover by pulling the latch slightly to the left as you close it.

Locating the reset button

To locate the reset button on your WGI Innovations nano camera, you must first open the battery compartment.

Opening the Battery Compartment:

• Ensure that the camera is facing up.
• Find the locking tab at the bottom of the camera and unlatch it.
• Slide the latch to the left to open the battery compartment cover.
• Once you have opened the battery compartment, look next to the battery compartment.
• Here, you should find the small reset button.

By pressing this button, you will be able to reset the settings on your WGI Innovations nano camera back to the original factory settings.

Returning to factory settings

To reset your WGI Innovations camera and return it to its factory settings, you will need to locate the reset button. This can be found next to the battery compartment. Once you have located the reset button, press it, and your camera will go back to its factory setting mode.

It is important to note that resetting your camera will delete all your customised settings and return them to how they were when you purchased the camera. Therefore, it is recommended to only reset your camera if you cannot fix any issues through other means.

Some common issues with the WGI Innovations camera include:

• No photos or videos saved on the SD card
• SD card getting stuck in USB mode
• LCD problems, such as a blurry or dark screen
• Blinking LED
• Photos being too dark or too bright

Before resetting your camera, you can try some troubleshooting steps to fix these issues. For example, if you are having issues with the SD card, try checking if it is attached correctly and if it has enough storage space. Additionally, ensure that you are using a compatible SD card and that you do not use the same SD card on multiple cameras. If you are experiencing LCD problems, check the battery life and ensure that the memory card is not locking the system.

Troubleshooting tips

• If your camera is not allowing you to access the menu mode to make adjustments, try removing the batteries and the SD card. If this does not work, try pressing the reset button.
• If your SD card is stuck in USB mode, it may be because you are using the wrong SD card. This issue happens when you use a card that doesn’t compete with your camera. The solution is to buy a new SD card.
• If your LCD screen is blurry, won't light up, or turns off, check if the batteries have enough charge. LCD shutting off is often caused by dead batteries.
• If the memory card locks the entire system, reset the camera and format the SD card. Set everything back as you did initially, and it should be back to normal.
• If your camera's LED is blinking, take out the SD card, format it, and put it back in the camera. If the problem persists, buy a new SD card.
• If your photos are too dark or too bright, check the exposure level. The marker on the scale should be in the middle or slightly on the positive side to keep the exposure in balance. Avoid setting the camera directly under the sun, as this will ruin the photos with too much brightness. Instead, position the camera facing north or south. If your photos are too dark, ensure that the camera is installed within range. Low-glow flashes will not provide enough light for proper visibility.
• If you continue to experience problems, take your camera to your nearest Wildgame Innovations trail camera service center if it is still under warranty. If it is not under warranty, you will need to pay for the repairs.

Checking the exposure level

Understanding Exposure:

Exposure refers to the amount of light that reaches the camera's image sensor. It is controlled by three main settings on your camera: ISO, aperture (f-stop), and shutter speed. These settings work together to create the desired exposure.

Checking Exposure on Your WGI Innovation Nano Camera:

• ISO Setting: Start by setting the ISO according to the lighting conditions. On your WGI camera, you can adjust the ISO by pressing the ISO button and turning the dial to select the desired value. In bright sunlight, a low ISO of 100 is usually sufficient. For overcast days or darker environments, you may need to increase the ISO to 400 or higher.
• Aperture (f-stop): The aperture controls the size of the lens opening and, consequently, the amount of light entering the camera. To adjust the aperture on your WGI camera, refer to the "A-mode" or aperture priority mode in your camera's settings. You can select different f-stop values to control the depth of field. For instance, a lower f-stop like f/2.8 will create a shallow depth of field with a blurred background. In contrast, a higher f-stop like f/16 will result in a wider depth of field with more elements in focus.
• Shutter Speed: Shutter speed determines how long the shutter remains open, affecting the amount of light that enters the camera. To adjust the shutter speed, locate the shutter speed setting in your camera's menu. Slower shutter speeds like 1/15 or 1/30 are suitable for low-light conditions but may require a tripod to prevent blurring due to camera shake. Faster shutter speeds like 1/500 or 1/1000 are ideal for capturing fast-moving subjects or freezing action.
• Using the Light Meter: Your WGI camera is likely equipped with a built-in light meter that helps you determine the correct exposure. This meter will indicate whether your image is over or underexposed by displaying values such as +1 (overexposed) or -1 (underexposed). Adjust your ISO, aperture, and shutter speed settings until the light meter reads "0," indicating a correct exposure.
• Exposure Compensation: In some cases, you may want to intentionally overexpose or underexpose your image. You can use the Exposure Compensation feature on your WGI camera to adjust the exposure level. This feature is usually represented by a +/- symbol and allows you to increase or decrease the exposure by a certain number of stops.
• Bracketing Exposure: Bracketing is a technique where you capture multiple images of the same scene with different exposure settings. Take a series of photos, some with higher exposure values (+1, +2) and others with lower exposure values (-1, -2). This gives you the option to choose the image with the desired level of brightness during post-processing.

Additional Tips:

• Always check your camera's manual to locate specific buttons and settings for adjusting ISO, aperture, and shutter speed.
• Experiment with different exposure settings to learn how they affect your images. Digital photography provides instant feedback, allowing you to review your photos and make necessary adjustments.
• When adjusting exposure, remember that changing one setting will require you to compensate with adjustments to the other settings to maintain proper exposure. For example, if you increase the ISO, you may need to decrease the aperture or shutter speed to avoid overexposure.

Replacing the batteries

To replace the batteries in your WGI Innovations nano camera, follow these steps:

Firstly, locate the reset button next to the battery compartment. The battery compartment is at the bottom of the camera. To open it, unlatch the door at the bottom of the camera.

Now, with the bottom of the camera facing towards you, insert two C-cell batteries. Ensure that the positive ends of the batteries are facing towards you in the left battery chamber, and the negative ends are facing towards you in the right battery chamber.

Do not mix old and new batteries. Also, do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc) batteries.

Once you have inserted the batteries, close the battery compartment cover. To latch the cover, pull the latch slightly to the left as you close it.

Now, check the battery level icon to ensure the batteries you have just installed contain the proper charge level. If so, you are good to proceed with camera use.

To turn the camera on, press and release the power button.

Frequently asked questions