Removing Nanit Camera: Detaching From The Stand Safely

how to remove nanit camera from stand

The Nanit baby monitor is a high-definition camera that can be affixed to a wall or floor stand. The floor stand can be freestanding or secured to the wall. The stand comes with a U-Clip wall mount with two parts, allowing for easy removal from the wall without disassembly. To detach the camera from the stand, you can use a sharp knife to cut behind the adhesive strips connecting the two. This will allow you to separate the camera without damaging the wall or the stand.

Characteristics Values
Camera resolution 1080p HD
Light Diffused, low glow, infrared light
Plastic Illuminating
Pairing button Radio signal icon
Reset button Small recessed button
Stand height 67 inches
Short stand segment length 9.6 inches
Long stand segment length 15 inches
Stand base width 12 inches
Cord cover ASTM-certified
Cord cover length 8 feet
Cord channel length 5 feet

shundigital

Removing the Nanit camera stand from wallpaper

To remove the Nanit camera stand from wallpapered walls without damaging the wallpaper, you can try a few different methods. One suggestion is to use a sharp knife, such as a pocket knife, to cut behind the adhesive strips attached to the wall. This will help to separate the adhesive from the plastic piece of the stand, allowing you to roll the adhesive off the wall.

Another method is to use painter's tape and heavy-duty Velcro. Affix the Velcro to the stand and to the painter's tape on the wall. When you need to remove the stand, simply peel the painter's tape off the wall. This method may be ideal if you don't want to screw the stand into the wall.

Additionally, if you have the Nanit floor stand, you can wrap the pole in extra wallpaper to camouflage it. This way, you won't have to attach it to the wall at all. Just be sure to place it securely as a free-standing structure.

shundigital

Using a knife to cut behind the adhesive strips

To remove the Nanit camera from the wall without damaging the wallpaper, you can use a knife to cut behind the adhesive strips. This method will allow you to cut the adhesive off from the plastic piece, so that you can then roll the adhesive off the wall without tearing the wallpaper.

  • Take a sharp knife, such as a pocket knife, and carefully insert it behind one of the adhesive strips. Be cautious and hold the knife firmly, but not too close to the blade, to avoid any accidental cuts or injuries.
  • Gently slide the knife behind the strip, using a slow and controlled motion, to avoid cutting or damaging the wall or wallpaper. Start from one end of the strip and gradually work your way across to the other side.
  • Apply just enough pressure to cut through the adhesive, but be careful not to press too hard, as you don't want to risk puncturing the wall or damaging the wallpaper.
  • Once you have cut through the adhesive behind one strip, slowly move to the next strip, repeating the process until you have cut through all the adhesive strips.
  • After cutting through all the adhesive, you can now carefully roll or peel off the adhesive strips from the wall, leaving the plastic piece intact. Ensure that you do this slowly and gently to avoid any accidental damage to the wallpaper.

By using this method, you can safely remove the Nanit camera from the wall, preserving your wallpaper, and creating a smooth surface for any future adjustments or relocations of the camera setup.

shundigital

Attaching the stand to the wall using Velcro and painter's tape

Firstly, gather your materials. You will need a sufficient amount of Velcro, painter's tape, and, optionally, a Nanit floor stand. The floor stand is useful if you want to keep the stand and camera mobile, but it is not necessary if you plan to affix the camera directly to the wall.

Next, prepare the wall. Ensure the wall surface is clean and dry. If you are using a floor stand, decide on the ideal height and position for the stand, and mark the spot on the wall with a pencil. If you are affixing the camera directly to the wall, you will need to position it so that it has a clear view of the crib.

Now, attach the Velcro. Take one strip of Velcro and firmly stick one side to the wall, or to the stand if you are using one. Repeat this process with another strip of Velcro, attaching it to the corresponding side of the stand or camera. Ensure that the Velcro strips align and will stick together securely.

Finally, secure the stand or camera to the wall. If using a stand, attach the painter's tape to the wall, pressing firmly to ensure adhesion. Then, stick the stand to the wall by pressing the corresponding Velcro strips together. If affixing the camera directly to the wall, use the painter's tape to stick one side to the wall, and the other to the camera, ensuring the camera is held securely.

This method provides a secure and adaptable way to attach your Nanit camera to the wall without causing damage. When you are ready to remove the setup, simply peel off the painter's tape, and your wall will be untouched.

shundigital

Adjusting the camera angle using the grey knob

Adjusting the camera angle of your Nanit baby monitor is a straightforward process. The camera's angle can be adjusted using the grey knob located near the top of the stand. This knob allows you to tilt the camera up or down to achieve the desired viewing angle.

To adjust the camera angle, start by turning the grey knob counter-clockwise. This will loosen the knob and allow you to move the camera freely. Once the knob is loosened, you can gently tilt the camera to the desired position. It is important to handle the camera with care and avoid applying excessive force during this process.

After positioning the camera, you will need to secure it in place. To do this, simply turn the grey knob clockwise to tighten it. Ensure that the knob is securely tightened to prevent the camera from accidentally moving out of position. Now you can rest assured that your Nanit camera is firmly locked in the desired angle.

The ability to adjust the camera angle is a valuable feature of the Nanit baby monitor. It ensures that you can always have a clear view of your baby's crib, providing peace of mind and allowing you to capture all the precious moments. Whether you need to adjust the angle for a better perspective or to accommodate changes in the nursery setup, the simple process of turning the grey knob makes it easy to achieve the perfect viewing angle.

shundigital

Detaching the camera from the stand using the U-Clip wall mount

To detach your Nanit camera from the stand using the U-Clip wall mount, you will need to follow a few simple steps. Firstly, make sure you have the U-Clip wall mount, which comes with two screws, ready to use. The U-Clip wall mount is included with your Nanit camera purchase and is designed to allow easy removal of the camera from the wall without any disassembly.

Next, secure the U-Clip to the stand by attaching it to the base of the stand. Then, carefully screw the clip to the wall, ensuring that the height from the floor is 32 inches, as recommended by Nanit. This step will ensure that your camera is securely mounted to the wall.

Now that your camera is mounted to the wall, you can detach it from the stand. To do this, carefully remove the camera from the stand by gently pulling it straight up and away from the stand. Ensure that you do not force it, as this may damage the product.

Once the camera is detached, you can now attach it to another stand or mount, allowing you to use it with another baby or in a different location. This process of detaching the camera from the stand using the U-Clip wall mount ensures that you can easily move your Nanit camera to different locations without any complicated disassembly or reassembly.

Frequently asked questions

The Nanit camera can be removed from the floor stand by loosening the grey knob near the top of the stand. Turn the knob counterclockwise to loosen it, then turn it clockwise to tighten it once you've removed the camera.

Yes, the Nanit camera can be mounted to a wall using the included U-Clip wall mount and two screws. The U-Clip attaches to the stand, and the entire assembly can then be screwed into the wall.

For the most secure and stable position, the U-Clip should be screwed to the wall 32 inches from the floor.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment