Replacing Moto G4 Plus' Back Camera Glass: A Step-By-Step Guide

how to remove moto g4 plus back camera glass

If you want to remove the back camera glass from your Moto G4 Plus, you'll first need to power off your phone and remove the back cover. Then, you'll need to remove the middle plate and disconnect the camera flash connector. Finally, you can use a tool like a spudger or a needle to gently pry off the back camera glass. It's important to be careful during this process to avoid damaging any other components. There are also replacement kits available online that come with tools and instructions for removing and replacing the back camera glass.

Characteristics Values
Ease of Installation Easy to install, straight-forward, simple
Quality Very good, effective, useful
Scratch Resistance Scratch-resistant, still good without a scratch
Image Quality Picture clarity is back, camera is working fine with better picture quality
Fit Fits perfectly, perfect fit for Moto G4 Plus
Value Worth the price, worth the money
Material Nice lens, made of excellent material

shundigital

How to remove the back cover of a Moto G4 Plus

To remove the back cover of a Moto G4 Plus, follow these steps:

First, power off your phone completely. This is an essential step before proceeding with any phone repairs or maintenance.

Now, you can begin to remove the plastic back cover. There is a small gap at the bottom of the phone where you can start to gently peel off the back cover. Insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charging port. Gently pry the back cover away from the body of the phone. Continue to lift the back cover carefully until all the plastic clips have been released.

Once the back cover is removed, you can access the internal components of the phone. If you need to replace the rear camera glass, be sure to purchase a compatible replacement part. You can find these online or at electronics stores. Keep in mind that some replacement parts may not come with installation instructions, so you may need to refer to online tutorials or videos for guidance.

Before installing the new camera glass, ensure that you have the correct tools, such as a spudger or tweezers, and a work area that is clean and well-lit. It is also recommended to wear eye protection and exercise caution to avoid damaging your device or injuring yourself.

Remember to test the new camera glass before completing the installation. Align the cover over the body of the phone and gently press around the edges until you feel the clips snap into place. Power on your device and test the camera to ensure it is functioning properly.

If you need to reassemble your device, simply follow these instructions in reverse order.

shundigital

Removing the Moto G4 Plus midframe

To remove the Moto G4 Plus midframe, follow these steps:

First, power off your phone and remove the plastic back cover. There is a small gap at the bottom of the phone where you can easily peel off the back cover.

Next, remove the middle plate by unscrewing all the screws on it using a T3 Torx screwdriver. Then, remove the rubber protective cover and release the connector underneath. Don't forget to take out your SIM and SD cards before removing the middle plate.

Now, you can remove the midframe. Loosen it along the edges and lift it away from the body of the phone. Be very careful not to puncture the battery with any sharp tools as a damaged lithium-ion battery can catch fire and/or explode.

Once the midframe is removed, you can proceed with other repairs or replacements, such as replacing the rear camera glass.

shundigital

Disconnecting the camera flash connector

To disconnect the camera flash connector on your Moto G4 Plus, follow these steps:

First, make sure you have downloaded the Rescue and Smart Assistant app to back up your device and check whether your problem is software or hardware-related.

Next, insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charging port. Gently pry the back cover away from the body of the phone and continue to lift it until all plastic clips have been released. Remove the back cover.

Now, slide out and remove the SIM card. Then, remove the nineteen 3.1 mm T3 screws securing the midframe.

Use the point of a spudger to pry up the rubber cover over the camera flash connector. Remove the rubber cover.

Finally, use the point of a spudger to pry up and disconnect the camera flash connector.

Be very careful not to damage any other components while performing these steps, especially the battery, as a damaged lithium-ion battery can catch fire and/or explode.

How ADT Monitors Your Security Cameras

You may want to see also

shundigital

Removing the rear camera with tweezers

To remove the rear camera with tweezers, follow these steps:

First, power off your Moto G4 Plus and remove the plastic back cover. There is a small gap at the bottom of the phone where you can easily peel off the back cover. Next, undo all the screws on the middle plate using a T3 Torx screwdriver. Remove the rubber protective cover and release the connector underneath. Before removing the middle plate, take out your SIM and SD cards.

Now, you can start to remove the rear camera. Peel off the gold protective tape and loosen the camera connector. Then, use tweezers to carefully lift and remove the rear camera from the motherboard.

It is important to note that there are other components attached to the motherboard, such as the front-facing camera and charging port, so be cautious when performing this step. Additionally, some online tutorials recommend using a spudger tool to assist with the removal of certain components, so consider having one on hand if needed.

shundigital

Reassembling the Moto G4 Plus

To reassemble your Moto G4 Plus, follow these instructions in reverse order.

Firstly, orient the new battery so that the wires exit near the bottom of the phone, and the battery connector is on the motherboard side. Clean off any adhesive residue that may prevent the battery from sitting flush against the frame. Use a few strips of adhesive included in the battery kit or some double-sided tape to secure the battery to the frame.

Next, during reassembly, align the connector in its socket, then press straight down to reconnect it. Use tweezers or your fingers to route the battery wires back through the plastic brackets.

Then, during reinstallation, align the vibration motor with its recess and press down. Use a spudger to pry up and reconnect the home button cable connector to the motherboard. Use a spudger to pry up and reconnect the display connector to the motherboard.

After that, for reinstallation, align and reinsert the cable into the ZIF connector so that the white line on the cable barely shows. Flip the ZIF connector lock back down.

Now, to reinstall the back cover, align the cover over the body and gently press all around the edges until you feel the clips snap into place.

Finally, to reassemble your device, follow these instructions in reverse order.

Frequently asked questions

You will need a replacement back camera glass lens cover, an adhesive, and some tools like tweezers and a spudger or needle.

First, you will need to remove the back cover of your phone. Then, you can use a tool like a spudger or a needle to pry off the old back camera glass. Be careful not to cut yourself on any glass splinters.

Clean off any adhesive residue from the old camera glass. Then, attach the new camera glass using the provided adhesive. Make sure to remove any protective plastic film from the new lens to avoid a blurry effect.

You can find replacement back camera glass lens covers for the Moto G4 Plus on websites like Amazon and eBay.

Replacing the back camera glass lens cover on your Moto G4 Plus is a fairly simple process that you can do yourself. However, if you are not confident in your ability to do it yourself, you can always take it to a local repair shop.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment