Removing The Lg 27Mk60tm Monitor Stand: A Step-By-Step Guide

If you're looking to remove the stand from your LG 27MK60TM monitor, you've come to the right place. This process can be a little tricky, but with the right approach, you'll be able to successfully separate the stand from your monitor without causing any damage. It's important to note that some stands may have a release mechanism or button, while others might require a bit more force to disconnect. In any case, it's always a good idea to refer to the manual for specific instructions or reach out to LG support for further guidance if needed.

Unscrew the bolts connecting the stand to the monitor

To remove the stand from your LG monitor, you will need to first place the monitor on a soft cloth on a table, to prevent the screen from getting scratched. Ensure that the monitor is turned off and unplugged.

Now, you will need to remove the bolts connecting the stand to the monitor. You can do this by holding the base of the stand with one hand and using your other hand to loosen the screws sticking out of the base. The stand is held in place by four screws, two on each side. Once the screws are removed, the stand should come off easily. If it doesn't, gently rock the stand back and forth until it comes loose.

If the base of the monitor gets stuck, loosen the screws slowly. If you do it in a hurry, the lower stand may break. You can also try using a small amount of mechanical oil on the joints to see if it budges.

Once the stand is loose, lift it off the monitor.

Lay the monitor flat on a soft surface

To remove the stand from your LG monitor, you will need to lay the monitor flat on a soft surface. This is an important step to ensure the safety of your monitor during the removal process.

Choose a soft, flat surface such as your bed or a large sofa. Make sure the area is clear of any objects that could scratch or damage the screen. If you wish, you can place a soft cloth or blanket on the surface for added protection.

Next, carefully lay the monitor down, screen-side up. Ensure that the screen is not facing down, as this could increase the risk of scratches or damage. Take your time with this step and handle the monitor with care.

With the monitor securely in place, you can now begin the process of removing the stand. Gently wiggle the stand to loosen it and carefully pull it away from the monitor. If the stand is difficult to remove, you may need to apply a small amount of force, but be cautious to avoid damaging the monitor.

By laying the monitor flat on a soft surface, you can safely remove the stand without causing harm to your device. This method ensures that your monitor remains stable and protected throughout the removal process.

Try to wiggle the stand to remove it

To remove the stand from your LG monitor, you will need to first remove all the cables connected to the monitor, including the power cable. Ensure that the PC is turned off and place a soft cloth on a table to prevent the monitor screen from getting scratched.

Now, lay the monitor flat on the soft cloth and gently wiggle the stand to try and remove it. You can also try to pull the stand straight out. There may be a catch or latching mechanism at the bottom of the stand that is connected to the monitor, so try to find a release button or a flathead trigger mechanism facing the monitor.

If the stand is still stuck, you can try using a small amount of mechanical oil on the joints to see if it budges. You can also try taping up the ports and using WD40, spraying a little around where the stand connects to the monitor, and then gently wiggling it upwards.

It is important to note that you should not hold the monitor by its screen when attempting to remove the stand. Instead, hold it firmly by the sides.

Use WD40 to spray around the connection

To remove the stand from your LG monitor, you can try using WD40. First, tape up the ports to prevent any spray from getting inside the monitor. Then, spray a little WD40 around the connection between the monitor and the stand. After that, gently wiggle the stand upwards to detach it from the monitor. This method has been reported to work by someone who had the same issue with their LG 27MN60T monitor.

It is important to note that this process may not be the official method recommended by LG, and there is a risk of damaging the monitor if not done carefully. It is always a good idea to refer to the official manual or seek professional help if you are unsure about the process.

Additionally, make sure to lay the monitor flat on a soft surface, such as a bed, before attempting to remove the stand. This will help prevent any damage to the screen during the removal process.

Remember to work gently and carefully, as forcing the stand may damage the monitor. If you encounter any issues or have concerns, it is recommended to consult a professional or refer to the official LG support resources for further guidance.

Gently wiggle the stand and pull it straight out

To remove the stand from your LG monitor, gently wiggle the stand and pull it straight out. This may take a bit of force, but it should come off. Lay the monitor flat on a soft surface, like a bed, and then wiggle the stand a bit to try and get it off. There's no latch or catch, so it's just a matter of wiggling it out and pulling straight up.

If you're having trouble, try using a flathead screwdriver to trigger the release mechanism facing the monitor. You can also try spraying some WD40 around the connection point and then gently wiggling the stand upwards.

Remember, there is a piece of metal coming from the monitor that is not removable, so the stand will only come off by pulling straight out.

Frequently asked questions