Removing The Acer Monitor Stand: A Step-By-Step Guide

If you're looking to remove the stand from your Acer monitor, there are a few methods you can try. Firstly, ensure that your monitor is turned off and unplugged, then lay it face down on a soft surface to avoid scratches. Some Acer monitor stands can be removed by simply pressing a release button near the bottom of the monitor and sliding the base out. However, for other models, you may need to unscrew the stand. This may involve removing a cover at the top of the back panel or snapping off a plastic cover over the hinge where the stand connects to the monitor. In some cases, you may need to remove the back of the monitor casing, which could void the warranty. It is important to be cautious and follow instructions specific to your model to avoid damage.

Power off the monitor and unplug all cables

Before you start disassembling your Acer monitor, it's important to take some safety precautions. The first step is to power off the monitor and unplug all cables, including the power cable and any other cables connecting it to your computer or other devices. This is a crucial safety measure to prevent any electrical hazards during the disassembly process.

When unplugging the cables, be gentle and avoid pulling on the cords forcefully. Use the appropriate connectors and ports to disconnect each cable properly. Once all the cables are unplugged, set them aside in a safe place where they won't be damaged or cause tripping hazards.

It's also a good idea to take note of which cable goes where. You can even take a picture of the cable setup before unplugging everything, so you can refer back to it when it's time to reassemble the monitor. This will ensure that you reconnect the cables correctly and avoid any potential issues.

Laying the monitor on a flat, sturdy surface is ideal for stability and easy access during the removal process. Make sure the surface is clear of any objects that could cause accidental damage to the monitor. Additionally, consider placing a soft cloth, towel, or blanket on the surface to protect the monitor from scratches or other types of damage. This is especially important if your work area is particularly hard or rough, as it provides a protective layer for your monitor's screen and body.

Once you have safely powered off the monitor, unplugged all the cables, and prepared your work area, you can proceed with the next steps to remove the monitor stand. Remember to take your time and be gentle during the entire process to avoid any accidental damage to your Acer monitor.

Lay the monitor face down on a soft cloth

To remove the stand from an Acer monitor, you'll need to first lay the monitor face down on a soft cloth, such as a towel or blanket, to protect the screen from scratches or damage. This is an important step as it ensures that your monitor remains in good condition during the removal process.

When laying the monitor down, take care to place it on a stable, flat surface. This will ensure that the monitor does not accidentally shift or slide during the removal process, which could potentially cause damage.

With the monitor securely in place, you can begin the process of detaching the stand. The specific steps for this will depend on the model of your Acer monitor. For example, for the KG270 model, you will need to unlock the screw that attaches the base to the monitor stand arm. This may require using a coin to loosen the screw.

For other models, such as the EG270, removing the stand may require more complex disassembly. This could include removing multiple sets of screws and even splitting the case halves of the monitor, which should be done with caution as it may void the warranty.

In some cases, the stand may not be designed to be removed at all. For instance, the stand for the Acer 165hz monitor (RG241YP) cannot be easily detached without removing the bottom panel of the monitor, which is secured with small plastic pieces that can break easily.

Therefore, it is important to carefully identify the model of your Acer monitor and research the specific steps required to remove the stand, being cautious of any potential risks or difficulties involved.

Unlock the monitor stand arm

To unlock the monitor stand arm of an Acer monitor, you must first ensure that the base is unlocked from the monitor stand arm. Place the monitor face down on a stable surface and check underneath for a screw that can be loosened with a coin. If there is such a screw, simply unlock it to disassemble the hinge assay.

For some models, such as the EG270, removing the base and arm is not enough to fully detach the stand. In this case, you will be left with a short metal piece that is attached to the monitor. To completely remove the stand, you would need to split the case halves of the monitor, which would likely void the warranty. Therefore, it is recommended to leave the metal piece in place, as it will not be visible once a desktop VESA mount is attached.

For other models, such as the X213Hbid, X233H, and AL1916W, the stand can be removed by popping off the cover on the back of the monitor where the stand connects. This can be done by squeezing the sides, prying with a flat-head screwdriver, or using your fingernail to get under the edge and pop it off. Once the cover is removed, you will see four screws that can be unscrewed to detach the stand.

Remove the base

To remove the base of your Acer monitor, start by turning off the power and unplugging all cables, including the power cable and any connection to your computer. This is important for your safety and to avoid damaging the monitor. Once that's done, you can lay the monitor face down on a towel, blanket, or soft cloth on a table. This will protect the screen from scratches or damage.

Now, you're ready to remove the base. Look for a release button near the bottom of the monitor, where the base and monitor meet. Press this button and slide the base out from the monitor. If your monitor has a screw at the bottom, you may need to loosen or unlock it with a coin before you can slide out the base.

If you have an Acer KG270 monitor, there might be a metal weight and three deeply set Philips head screws inside the tower piece that you'll need to remove. You may need an extra-long Philips-head screwdriver for this. Then, using two flathead screwdrivers, push down the plastic tab in the middle with one screwdriver, and with the other, wedge between the plate and the monitor to get it off the plastic tab.

For the Acer EG270 monitor, after removing the base, you'll find two slot screws at the bottom of the rectangular base. Remove these, and then take off the small rectangular metal plate at the bottom of the plastic arm. This will reveal three Philips head screws that you can also remove.

If you're still having trouble, check for a cover or cowling at the back of the monitor, near the hinge where the stand connects. This can be pried off with your fingers or a flat-head screwdriver, revealing screws that hold the stand in place.

Unscrew the stand

Unscrewing the stand is a delicate process that requires careful attention to detail. Here is a step-by-step guide to help you successfully unscrew and remove the stand from your Acer monitor:

Step 1: Prepare the Monitor

Place the monitor face-down on a soft, flat surface to protect the screen from scratches or damage. Ensure that the power is turned off and all cables connected to the monitor are unplugged.

Step 2: Locate the Cover

On the back of the monitor, locate the cover or cowling that surrounds the hinge where the stand connects to the monitor. This cover may appear to be seamlessly attached to the monitor, but it is a separate piece that can be removed.

Step 3: Remove the Cover

Using your fingers or a flat-head screwdriver, gently pry or pop off the cover. It should have several snap points attaching it to the back of the monitor. Be careful not to apply too much force, as these snap points can be delicate.

Step 4: Expose the Screws

Once the cover is removed, you will expose the screws holding the stand in place. There should be at least two screws, but some models may have up to four or more screws.

Step 5: Unscrew the Stand

Using a suitable screwdriver, carefully unscrew the screws that secure the stand to the monitor. Make sure to keep track of the screws, as you will need to re-attach them if you ever need to re-assemble the stand.

Step 6: Remove the Stand

After unscrewing the stand, gently pull it out and away from the monitor. The stand should come off completely, leaving you with a stand-less monitor.

It is important to note that some Acer monitor models may have slight variations in the stand removal process. Additionally, removing the stand may void your warranty, so it is recommended to check your warranty information before proceeding.

Frequently asked questions