Are Rexing Dash Cams Charging? A Quick Guide To Know

how to kbbnow if rexing camera are charging

Rexing cameras are designed to be used while connected to a power source. The internal battery is intended for emergency situations only and will only record for a few minutes when disconnected from a power source. To know if your Rexing camera is charging, make sure the cable is connected correctly. The cord should sweep towards the front of the camera, not towards the mount. If you are having trouble getting it to charge, try rotating the connection at the camera by 180 degrees. You should see a flashing white light and hear an audible chime when the camera is charging.

Characteristics Values
How to know if charging A white light will appear above the camera lens
How to charge Plug in with provided cable
Internal battery use For emergency situations only
Hardwire kit Sold separately

shundigital

Check the internal battery

The internal battery of Rexing cameras is intended for emergency use only. It is designed to provide around 5-10 minutes of recording time after the camera has been disconnected, for example, if it is dislodged after an accident. The internal battery is not meant to be the camera's primary power source.

To check the internal battery, you can try disconnecting the camera from its power source and observing whether the camera stays on. If the camera immediately turns off when disconnected, the internal battery may not be functioning properly.

Another way to check the internal battery is to examine the battery itself. If you open up the camera, you can inspect the battery for any signs of damage or swelling. If the battery appears swollen, this could indicate that it needs to be replaced.

It is recommended to keep your Rexing dash cam plugged into a power source at all times or to manually hardwire it. This will ensure that you don't miss any important footage due to a depleted internal battery.

If you suspect that your Rexing camera's internal battery is not functioning correctly, you may need to replace it. You can find replacement batteries online, and the replacement process typically involves soldering new wires to the battery and the circuit board. However, it is always best to refer to the official user manual or seek professional help if you are uncomfortable with performing the replacement yourself.

shundigital

Check the power supply and demand

To check the power supply and demand of your Rexing camera, you can refer to the following steps and recommendations:

  • Ensure that your Rexing dash cam is connected to a power source while recording. The camera should be plugged into the included 12V car power cable or a compatible hardwire kit. The internal battery is designed for emergency situations only.
  • Check that you are using the correct power cable. The Rexing camera comes with an in-car power cable that is 12 feet long.
  • Consider purchasing a Rexing Smart Hardwire Kit. This kit allows for a cleaner installation without the need for a cigarette lighter plug. It also enables the parking mode feature, which automatically turns on the camera when it detects vibration or can be set to record 24/7.
  • If you are experiencing issues with your camera turning off shortly after disconnecting from a power source, try using a different power source.
  • Be mindful of the power demands of your Rexing camera. While the camera can be plugged into a car USB port, it may not provide sufficient power. It is recommended to use the car charger that comes with the dash cam or the Rexing Smart hardwire kit.
  • If you are experiencing issues with your camera's power, try updating the firmware to the latest version. This can help resolve any bugs or issues with the camera's performance.
  • If you continue to experience problems with your Rexing camera's power supply and demand, refer to the troubleshooting section in the user manual or contact Rexing customer support for further assistance.

shundigital

Check the camera's power supply

To check the camera's power supply, start by locating the power cable. The Rexing dash cam should have come with an in-car power cable that plugs into the cigarette lighter in your vehicle. Make sure this cable is securely plugged in on both ends.

If your camera is hardwired into your vehicle's electrical system, check the fuse box to ensure that the fuse has not blown. If you're unsure which fuse controls the camera, try checking your vehicle's manual or contacting a professional.

If your camera is not receiving power, try plugging the power cable into a different outlet or, if hardwired, into a different fuse. It is also possible that the power cable itself is faulty. Try using a different cable, if possible, to see if that resolves the issue.

If your camera is still not receiving power, there may be an issue with the camera itself. Try contacting Rexing customer support for further assistance.

shundigital

Check the camera is plugged in properly

To check if your Rexing camera is plugged in properly, you should first check that the camera is connected to a power source while recording. The camera should be plugged into the included 12V car power cable or a compatible hardwire kit. The internal battery is only meant for emergency situations, so it is important to ensure that the camera is plugged in properly during recording.

To check that the camera is plugged in properly, you can try plugging the camera into a cell phone charger to see if it powers on. If the camera powers on, then the issue may be with the 12V adapter. Check that the adapter is fully pushed in on both ends. If the adapter is properly connected, then the issue may be with the power adapter itself.

If the camera does not power on when plugged into a cell phone charger, then the issue may be with the camera itself. Try plugging the camera into a different power source, such as a computer, to see if it charges. If the camera still does not charge, then you may need to contact Rexing support for further assistance.

shundigital

Check the camera's charging circuitry

If your Rexing camera is not charging, it could be due to a faulty charging cable or a depleted battery.

Firstly, ensure that your camera is plugged in properly. Check that the charging cable is inserted correctly into both the camera and the power source. If the camera is plugged in properly and still won't charge, try using a different power source.

If you've tried a different power source and your camera still won't charge, the charging cable may be damaged and need replacing. Try using a different cable that is compatible with your camera.

If your Rexing camera still won't charge, the issue could be with the camera's battery or motherboard. The battery may be damaged and need replacing, or the motherboard could be faulty. In these cases, you will need to follow a repair guide to replace the battery or motherboard.

Other Troubleshooting Tips

  • Ensure your camera is connected to a power source while recording. Rexing dash cams are designed to be connected to a power source while in use, as the internal battery is only meant for emergency situations.
  • Try using a different power source. Your dash cam battery may be depleted.
  • If your camera uses a MicroSD card, check that it is inserted correctly and is compatible with your camera.
  • Update your camera to the latest firmware.
  • Restore your camera to factory settings and format the memory card.
  • If you're having trouble inserting the memory card, try using a coin to push it into place.
  • If your camera won't turn on, try holding down the 'OK' button to check its connection status, SSID, and password.
  • If your camera uses an app, ensure that you have installed the latest version and that your browser is up to date.

Frequently asked questions

When you plug the camera into a power source, a flashing white light will appear, and you will hear an audible chime.

If your camera is not holding a charge, the internal battery may be faulty. Try charging the camera for a few hours, and if that doesn't work, use the reset button and upgrade the firmware. If this still doesn't work, you may need to replace the internal battery.

The Rexing V1P Pro is hardwired, so it should turn on automatically when you start your car. If it doesn't, the power supply may be faulty, or the internal capacitor may need recharging.

The capacitor in your Rexing camera does not need to be charged. It will charge automatically when the camera is plugged into a power source or hardwired.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment