Powering Up: Replacing Camera Batteries For A Fresh Start

Replacing the battery in a camera is a relatively simple process, but it can vary depending on the camera model. Some cameras, such as the Reolink Argus 2 and Argus Pro, allow users to replace the battery by pulling a button, sliding the battery upwards, and removing the rechargeable battery. Other cameras, like the Reolink Go and Go Plus, require users to open the back cover by twisting it before removing the battery. It's important to note that some cameras, such as the Google Nest camera, have batteries that are not replaceable and need to be charged. Additionally, certain cameras may require technical knowledge for battery replacement, and it is recommended to seek professional service for those models. It is generally advised to turn off the camera before replacing the battery to avoid potential data loss or corruption of memory cards.

Canon PowerShot G2: remove the battery pack, pull out the battery holder, push up the edge of the date battery, insert a new one, and close the cover

To replace the date/time battery on the Canon PowerShot G2, follow these steps:

First, turn off the camera's power. Then, open the battery cover by sliding it in the direction of the arrows.

Now, you need to remove the battery pack. Do this by pulling out the battery holder—you can do this by hooking your fingertip under the bottom edge of the battery holder and gently pulling.

Next, use your fingertip to push up the edge of the date battery, and then pull it out in the direction of the arrow. The new date battery you insert should be a generic CR2016 lithium coin battery, with the negative terminal (-) facing upward. Place the new battery into the date battery holder, and then replace the date battery holder and the battery pack. Finally, close the battery cover.

This procedure will reset your camera to its factory default settings, so you will need to reset the date and time.

Reolink Argus 2/Argus Pro: pull the button, slide the battery up, remove, and replace

To replace the battery of a Reolink Argus 2 or Argus Pro, follow these steps:

First, take a look at the different parts of the camera to familiarise yourself with its components. Then, locate the button as shown in the picture, and pull it. Next, slide the battery upwards to remove it from its housing. Once the rechargeable battery is removed, you can replace it with a new one.

It is important to note that only the battery in the camera models Argus 2, Argus Pro, Go, Go Ultra, and Go Plus can be removed. The batteries in other Reolink battery-powered cameras are rechargeable but not replaceable. Therefore, if you own a different model, you may need to contact customer support or refer to their official website for further guidance on battery replacement.

By following these steps, you will be able to safely and effectively replace the battery in your Reolink Argus 2 or Argus Pro camera, ensuring your device continues to operate optimally.

Reolink Go/Go Plus: open the back cover, pull out the battery, and replace

To replace the battery for a Reolink Go or Go Plus camera, first, open the back cover by twisting it a little. Then, pull out the battery and replace it with a new one.

It is important to note that only the battery in the Reolink Go, Go Plus, Argus 2, Argus Pro, and Go Ultra camera models can be removed. For other Reolink battery-powered cameras, the batteries are rechargeable but not replaceable.

Reolink sells replacement batteries for the Reolink Go and Go Plus on their website or official store. You can also contact Reolink Support if your battery is faulty and covered by their two-year warranty.

The Reolink Go and Go Plus cameras have rechargeable batteries that can be removed from the camera body. The back cover, which houses the batteries, can be twisted open to access the battery for removal and replacement.

There are three methods to charge the Reolink Go and Go Plus batteries:

• Charge the battery separately: Open the back cover, pull out the battery, and connect it to a USB adapter via a USB cable.
• Charge the camera with the battery inserted: Connect the camera directly to a USB adapter using a USB cable.
• Charge the camera with a Reolink Solar Panel (sold separately).

Google Nest: the batteries are not replaceable

Some Google Nest products have batteries that need to be replaced periodically. The Nest Thermostat, for example, uses two standard 1.5 V AAA alkaline batteries as a backup or supplementary power source if your system can't deliver enough power. The Nest Temperature Sensor, on the other hand, uses a disposable 1 CR2 3V Lithium battery that needs replacement when depleted.

It is important to note that while some Nest products have replaceable batteries, others do not. The Nest Thermostat E, Nest Learning Thermostat, and Nest Connect have internal rechargeable batteries that are not user-replaceable. These batteries are designed to constantly charge and discharge as needed throughout the life of the product. Therefore, if you encounter issues with these devices not turning on or holding a charge, it is likely due to insufficient power from your household wiring, rather than the batteries needing replacement.

For Nest products with replaceable batteries, such as the Nest Thermostat, it is important to follow the correct replacement procedure. First, pull the thermostat display off the base. Remove the old batteries and insert two new AAA alkaline batteries, ensuring they are facing the right way. Finally, push the thermostat display back onto the base until it clicks into place.

In summary, while some Google Nest products have replaceable batteries, others, like the Nest Thermostat E, Nest Learning Thermostat, and Nest Connect, have internal rechargeable batteries that are not designed to be user-replaceable. It is important to refer to the specific product's instructions to correctly identify and replace batteries when needed.

Canon EOS 80D: no need to power off, but may lose data being written to the card

The Canon EOS 80D is a digital single-lens reflex (DSLR) camera that uses the LP-E6N battery model. This model is also compatible with other Canon EOS cameras, such as the 5D, 60D, 70D, and 90D.

When replacing the battery for the Canon EOS 80D, there is no explicit requirement to power off the camera. However, it is generally recommended to turn off electronic devices before removing or replacing their batteries as a safety precaution.

While powering off the Canon EOS 80D before changing its battery may not be mandatory, there are potential consequences to performing this action with the camera still on. The primary concern is data loss. If the camera is powered on and in the process of writing data to the memory card when the battery is removed, that data may be lost or corrupted. This could include photos, videos, or settings that have not been saved yet.

Therefore, while it may not cause immediate harm to the camera, it is advisable to power off the Canon EOS 80D before replacing the battery to minimize the risk of data loss. This simple step can help ensure that your captured memories and customized settings remain safe and intact.

Frequently asked questions