Removing The Asus Monitor Stand: A Step-By-Step Guide

how to take asus monitor stand off

If you're looking to remove the stand from your Asus monitor, it's important to know that there are different types of stands, and the process of removing them can vary. Most monitor stands consist of three components: the base, the vertical stand, and the connector. The process can be tricky, and you may break the stand if you don't have enough knowledge. Before beginning, make sure to refer to your monitor's user manual for specific instructions. In general, you will need to remove the base, then the vertical stand, and finally the connector or vertical stand holder. This will often involve removing screws with a screwdriver, but be sure to also check for hooks or buttons that may be used to secure the stand.

Characteristics Values
Number of components 2-3
Base The surface of the stand
Vertical stand The part that stays upright and is connected to the base
Connector Connects the stand to the monitor
Tools Screwdriver, stiff pointed tool (e.g. metal spudger), flathead screwdriver
Steps 1. Remove the base by unscrewing or rotating anti-clockwise. 2. Remove the vertical stand by unscrewing or pulling away from the monitor. 3. Remove the connector or vertical stand holder by unscrewing and removing the back panel.

shundigital

Remove the base

To remove the base of an Asus monitor stand, you must first lay the monitor face down on a smooth, clean, hard surface. Place a cloth underneath the screen to prevent it from getting scratched.

Next, look closely at the bottom surface of the base. Here, you will find either a screw or a hook. If there is a hook, rotate it in an anti-clockwise direction to remove it. If there is a screw, use a screwdriver to remove it. Now, gently remove the base plate from the vertical stand.

The shape of the base does not matter—the process for removing it remains the same. The base could be rectangular, circular, triangular or an arc.

If you are removing the stand to access the internals of your monitor, you will need to continue by removing the back part of the monitor.

shundigital

Remove the vertical stand

Once you have removed the base, check the vertical stand for a connection point. This section likely connects it with the vertical stand holder. However, some monitors may not have this component.

In some monitors, the vertical stand is directly connected to the monitor, while in others, the vertical stand connects to a holder that comes out of the back of the monitor. You need to refer to the user manual to know how the stand connects to your monitor.

To remove the vertical stand, first check for any screws holding it in place. If there are screws, remove them, then remove the stand. If there are no screws, check for any buttons near or on the vertical stand.

Some monitors, like Dell and Acer, have a dedicated button that you need to press to remove the vertical stand. Press the button and pull the stand outwards. If the stand still does not come out of the monitor, you can use a small amount of mechanical oil on the joints to see if it budges.

If the vertical stand has no screws or buttons, you may be able to remove it by gently pulling the stand away from the monitor. While doing so, make sure not to hold the monitor by its screen, but instead, hold it firmly by the sides.

Please refer to the user manual if you are having issues removing the vertical component.

Asus MX239 monitor

If you own an Asus MX239 monitor, first remove the base, then remove the two screws on the back of the monitor. Take them off and take out the back cover. You will then see three screws. Take them off using a screwdriver and now remove the vertical stand.

Asus ROG monitor

If you own an Asus ROG monitor, first remove the base and then take a look at the back of the monitor. You will find a circular plastic cover. Use a screwdriver to remove the plastic cover. After removing the cover, you will see four screws. Take them out by using a screwdriver. And remove the vertical stand from there.

shundigital

Remove the connector/vertical stand holder

To remove the connector or vertical stand holder, you will need to remove the back panel of the monitor. This is because the stand holder is connected to the monitor from the inside.

First, remove the screw from the back of the monitor. Then, gently take out the back panel, being careful to remove all the cables connecting to the ports and buttons on the panel. Once the back panel is free, you will be able to see some screws. Remove these and take out the connector from the back panel of the monitor.

Now that you have removed the connector, you have successfully removed your Asus monitor stand.

If you are unsure about disassembling the monitor, it is recommended that you take it to a local electronic repair shop to remove the connector.

shundigital

Take precautions to protect the screen

Before you begin, lay the monitor face down on a smooth, clean, flat surface. This will prevent the screen from getting scratched or damaged. It is also recommended to cover the surface with a soft cloth to protect the screen.

Next, remove all cables connected to the monitor, including the power cable and any other cables from the PC. This will ensure that you don't accidentally damage any cables during the process.

Now, you can start removing the components of the monitor stand. Depending on your monitor, there may be two or three components: the base, the vertical stand, and the connector. The base is the surface of the stand, the vertical stand is the upright part connected to the base, and the connector attaches the stand to the monitor.

First, remove the base by inverting the monitor and looking for a screw that holds it in place. Most monitors have a hook that you can rotate anti-clockwise to remove the screw. Once the screw is removed, gently take out the base plate.

Then, check for any connection points in the vertical stand. This part may be directly connected to the monitor or attached to a holder that comes out of the back of the monitor. Refer to your user manual to understand how the stand connects to your specific monitor. To remove the vertical stand, look for screws holding it in place and remove them. If there are no screws, check for buttons near or on the vertical stand. Some monitors have a dedicated button that you need to press to remove the stand. Gently press the button and pull the stand outwards. If it's still stuck, a small amount of mechanical oil on the joints may help. If there are no screws or buttons, you may be able to remove it by gently pulling the stand away from the monitor, being careful not to hold the monitor by its screen.

Finally, to remove the holder that connects the vertical stand to the monitor, you may need to remove the back panel of the monitor. This component is often connected from the inside, so you might need to take the monitor to an electronics repair shop if you're unsure about disassembling it further.

Throughout the process, be very careful not to apply too much force or use tools that could damage the screen. Always handle the monitor with care and follow the specific instructions for your monitor model to ensure the safest approach.

shundigital

Refer to the user manual

To take the stand off your ASUS monitor, refer to the user manual for detailed instructions. The manual will provide specific guidance on how to safely remove the stand without causing any damage to the monitor.

In the absence of a user manual, here is some general advice on how to proceed. First, ensure that you have laid the monitor face down on a smooth, clean surface. This will give you access to the rear of the monitor where the stand is typically attached.

Locate the screws securing the monitor stand. On some ASUS models, these screws may be hidden under rubber covers or plastic plates. You can use a stiff pointed tool, such as a metal spudger or a flathead screwdriver, to carefully pry off these covers and access the screws. Once the covers are removed, use the appropriate tool to unscrew and detach the stand from the monitor.

It is important to follow the specific instructions provided by ASUS for your particular monitor model to ensure the process is safe and effective. The user manual will also provide important safety precautions and guidelines to avoid any potential damage to the monitor during the process.

If you do not have access to the user manual, you can try contacting ASUS customer support or searching for the manual online. It is important to have all the necessary information before attempting to remove the stand to ensure the process is safe and does not void any warranties.

Frequently asked questions

Place the monitor face down on a flat surface. Look for a screw that holds the base in place. If there is a hook, rotate it in an anti-clockwise direction to remove the screw. If not, use a screwdriver to remove the screw. Now, gently remove the base plate from the vertical stand.

After removing the base, check for a connection point in the vertical stand. This will likely connect it with the vertical stand holder. Refer to the user manual to understand how the stand connects to the monitor. To remove the stand, check for any screws holding it in place and remove them. If there are no screws, check for any buttons near or on the vertical stand. Some monitors have a dedicated button that you need to press to remove the stand. If the stand still does not come off, use a small amount of mechanical oil on the joints. If there are no screws or buttons, try gently pulling the stand away from the monitor.

To remove the connector or vertical stand holder, you will likely need to remove the back panel of the monitor as this component is connected to the monitor from the inside. If you are unsure about disassembling the monitor, take it to a local electronic repair shop.

Make sure the monitor is switched off and unplugged. Wear an anti-static wrist strap and avoid any batteries inside the monitor. Place the monitor on a solid surface and use a cloth underneath the screen to prevent scratches. Before removing any screws, take a reference photo of the current layout and use the correct screwdriver type. Keep all the screws together. If you feel you cannot remove the stand, seek expert help.

First, check for any VESA locking screw and remove it if present. Next, release the VESA plate by pressing down on the plastic tab. Finally, remove the monitor cables and lift the monitor from the VESA mount.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment