Eliminating Rtsp From Wyze Cameras: A Comprehensive Guide

Real Time Streaming Protocol (RTSP) is a standard network protocol that allows users to establish and control media sessions between endpoints. It is used to stream videos from a Wyze camera to other platforms. However, due to hardware limitations, RTSP can only be achieved on a Wyze camera through separate firmware, which is currently in beta and may include minor stability issues. This firmware is not compatible with Wyze Cam v1. This article will provide a step-by-step guide on how to remove RTSP from your Wyze camera and address any issues that may arise.

Downloading the Wyze Cam RTSP file

To download the Wyze Cam RTSP file, you will need to follow a few simple steps. Firstly, you will need to download the correct RTSP file for your specific Wyze Cam model. The available models that support RTSP are Wyze Cam v2, Wyze Cam v3, and Wyze Cam Pan. It is important to note that the RTSP firmware is not available for Wyze Cam v1 due to hardware limitations.

Once you have downloaded the correct RTSP file, you will need to unzip the file and extract the contents. For Wyze Cam v2 and Pan, you will need to rename the file to 'demo.bin'. For Wyze Cam v3, the file should be named 'demo_wcv3.bin'. After renaming the file, transfer it to the root directory of a microSD card.

The next step is to unplug your Wyze Cam and insert the microSD card with the RTSP file. Then, hold down the camera's Setup button while plugging in the USB cable. Continue holding the Setup button until the light turns solid blue for Wyze Cam v2 and Pan, or solid purple for Wyze Cam v3. Note that for Wyze Cam v3, the blue and red LEDs will be on simultaneously, creating a solid purple colour.

Once the light is solid blue or purple, release the Setup button and wait for approximately 3-4 minutes. During this time, the camera will reboot, and the status light may change. After the process is complete, your Wyze Cam should appear on the Home tab without requiring a new setup, provided it was previously paired with your account.

Renaming and transferring the file to a microSD card

To remove RTSP from your Wyze camera, you will need to reset the camera to its original settings. This will involve downloading new firmware and transferring the file to a microSD card.

First, download the appropriate firmware file for your Wyze camera model. For the Wyze Cam v2 and Pan, you will need to download the Wyze Cam v2 RTSP file. For the Wyze Cam v3, you will need the Wyze Cam v3 RTSP file.

Once you have downloaded the correct file, unzip it and locate the file named 'demo.bin' within the unzipped folder. If you are using the Wyze Cam v3, the file will be named 'demo_wcv3.bin' instead.

Now, rename this file to 'demo.bin'. This step is important, as it ensures that the camera recognises the file during the boot-up process.

Next, insert your microSD card into your computer or device. You will need to transfer the 'demo.bin' file to the root directory of the microSD card. This means placing the file directly on the microSD card, not within any folders.

After the file has been transferred, safely remove the microSD card from your computer or device. Your microSD card now contains the necessary firmware to remove RTSP from your Wyze camera.

Note: It is important to ensure that you are downloading the correct firmware file for your specific Wyze camera model. Using incorrect firmware may cause issues with your camera's functionality.

Unplugging the camera and inserting the microSD card

To remove RTSP from your Wyze camera, you will need to reset the camera to its original settings. This will involve unplugging the camera and inserting the microSD card.

First, ensure that your camera is unplugged and powered off. Then, locate the microSD card slot on your camera. The slot is usually found on the side or bottom of the camera, depending on the model. Gently insert the microSD card into the slot, ensuring that it is properly aligned and pushed in securely.

If you are using a Wyze Cam v2 or Pan, you will need to unzip the RTSP file and rename the content to "demo.bin" before transferring it to the microSD card. For the Wyze Cam v3, the file should be named "demo_wcv3.bin". The file should be placed in the root directory of the microSD card.

Once the microSD card is inserted and the appropriate file is transferred, you can proceed to the next step of resetting your Wyze camera to its factory settings. This process will vary depending on your specific camera model.

It is important to note that resetting your Wyze camera will erase all existing data and settings. Ensure that you have backed up any important data before proceeding. By unplugging the camera and inserting the microSD card, you have completed the necessary steps to prepare for the reset process.

Holding the camera's setup button while plugging in the USB cable

To remove RTSP from your Wyze camera, you will need to reset the camera to its original settings. This will involve downloading the original firmware, copying it to a microSD card, and reinstalling it on the camera.

• Download the original firmware file for your specific Wyze camera model from the Wyze website.
• Unzip the downloaded file and locate the 'demo.bin' file within.
• Copy this 'demo.bin' file to the root directory of a microSD card.
• Turn off your Wyze camera by unplugging the USB cable.
• Insert the microSD card into the camera.
• Hold the camera's setup button and plug the USB cable back into the camera.
• Continue holding the setup button and wait until the LED light turns solid blue for Wyze Cam v2 and Pan, or solid purple for Wyze Cam v3. Note that for Wyze Cam v3, the light will appear purple as both the blue and red LEDs will be on at the same time.
• Once the LED light turns solid blue or purple, release the setup button.
• Allow the camera to reboot, which should take around 3-4 minutes. The status light will change during this time.
• Once the camera has finished rebooting, it should be reset to its original settings without RTSP enabled.

By following these steps, you will remove RTSP from your Wyze camera and restore it to its original firmware settings. This process will reset the camera to its default configuration, and you may need to set up your camera again from the beginning.

Accessing the RTSP function from the live stream

To access the RTSP function from the live stream, you need to have the Wyze app version 2.3 or later.

Once your Wyze Cam is back online, open the Wyze app and go to Settings > Advanced Settings > RTSP.

The app will then automatically check if the installed firmware version is RTSP compatible. If it is not, you will need to repeat the installation process.

Next, turn on the RTSP toggle. You will then be prompted to set up a username and password for this Wyze Cam. It is important to note that this username and password are unique to this camera only. Ensure that you use something memorable or take note of them as they will be needed to access the camera's stream via RTSP.

Finally, click “Generate URL”. The RTSP URL will then be displayed on the next screen. This URL can be used for streaming through any RTSP-compatible player on the same local network as the Wyze Cam.

Frequently asked questions