Dismantling A Monitor: Removing The Base Stand Safely

Removing the bottom of a monitor is a process that can vary depending on the make and model of the monitor. It is important to refer to the user manual for specific instructions, as attempting to force the removal can result in damage. In general, the process involves unplugging the monitor and placing it on a flat surface, either face down or on its side, to avoid screen damage. The next steps typically involve locating and manipulating locking mechanisms, such as tabs or knobs, that secure the base to the monitor. These mechanisms may be found on the sub-base or the bottom of the monitor itself. By sliding, pulling, or turning these locks, the base can be released and removed. In some cases, additional screws may need to be removed to fully detach the monitor's bottom. It is always recommended to consult official guides or seek expert advice before attempting any disassembly.

Unplug the monitor power cord from the power source

Before you begin to disassemble your monitor, it is important to ensure that it is switched off and unplugged from the power source. This is a crucial safety precaution to prevent any potential electrical hazards.

To start, locate the monitor power cord at the back of the monitor. The power cord is typically a thick cable that connects the monitor to a power outlet or power strip. Grasp the power cord firmly and gently pull it out of the power outlet or power strip. If the cord feels stuck, you can try wiggling it gently from side to side while pulling to loosen the connection. Ensure that you pull from the cord itself and not the cable, as pulling on the cable can cause damage or create a safety hazard.

Once the power cord is unplugged, you can proceed to disconnect the monitor cables from the computer. These cables include the video cable (usually VGA, DVI, HDMI, or DisplayPort) and any other peripheral cables such as USB or audio cables. Gently pull each cable out of its respective port on the back of the monitor. Again, if a cable feels stuck, wiggle it gently while pulling to loosen the connection.

Now that the monitor is completely disconnected from power and peripherals, you can safely place it on a flat surface or towel, as described in the next steps for removing the monitor base. It is always important to handle electronic equipment with care and ensure that you are working on a stable, secure surface to avoid any accidental damage to your monitor.

Remember to consult the user manual for your specific monitor model if you have any concerns or if your monitor differs from the standard setup. Taking these precautions will help ensure that you can safely and effectively remove the bottom of your monitor without causing any damage or encountering any safety issues.

Disconnect the monitor cables from the computer

To disconnect the monitor cables from your computer, you will need to first unplug the monitor power cord from its power source. Place a towel on a flat surface and lay the monitor on its side on the towel to protect the screen from damage.

The next steps will depend on the type of monitor you have. If you have a standard monitor, the base is attached to the monitor by a sub-base. Slide the monitor base forward to access the locking tab on the sub-base. Pull up on the locking tab with your thumb and slide the sub-base towards the front of the monitor. You can then remove the sub-base and base away from the monitor.

If you have an LCD flat-screen monitor, the base locks onto a stem at the back of the monitor. Place the monitor screen-side down on a towel over a flat surface. Locate the locking knob on the bottom of the base and turn it counterclockwise 90 degrees with your fingers. Pull the base off the monitor.

If you are disconnecting an external monitor, you can simply unplug the VGA or HDMI cord that is connected to your laptop. However, this method may cause damage to your display ports over time. Alternatively, you can use the Windows Settings app to disconnect the monitor without unplugging the cable. Press the "Windows key + P" keyboard shortcut and select the "PC screen only" option. This will automatically disconnect your second monitor.

Place the monitor on its side on a towel

To remove the bottom of a monitor, you'll first need to place the monitor on its side on a towel. This is an important step to protect the screen from damage. Choose a towel that's large enough to accommodate the monitor and place it on a flat, even surface to ensure stability. Make sure the screen is facing away from the surface to avoid any accidental scratches.

Once you've placed the monitor on its side, you can begin the process of detaching the base. For an LCD flat-screen monitor, you'll typically find a locking mechanism or a tab that connects the base to the stem at the back of the monitor. For standard monitors with curved screens, you may need to slide or pull the base forward to access this locking mechanism.

Before proceeding, make sure the monitor is unplugged and all cables are disconnected. This is a safety precaution to avoid any electrical hazards. Additionally, it's easier to handle the monitor when it's not encumbered by cables.

Now, let's focus on the specific steps for placing the monitor on its side on the towel. Here's a detailed breakdown:

• Choose a workspace: Select a spacious and clear area to work on. This could be a table or a flat countertop.
• Prepare the towel: Lay out a clean towel on your chosen workspace. Ensure the towel is large enough to accommodate the monitor's size, with some extra room to prevent the monitor from rolling or slipping off.
• Position the monitor: Gently place the monitor on its side, with the screen facing away from the towel. Be careful not to apply pressure on the screen itself. Hold the monitor by its edges or sides to avoid touching the screen.
• Stabilize the monitor: Ensure the monitor is stable and won't roll or slide off the towel. You may want to place some soft objects, like folded fabric or foam, near the edges of the monitor to act as bumpers and provide additional stability.
• Prepare tools: If you need any tools to detach the base, such as a screwdriver, have them within easy reach. This will ensure that you don't need to leave the monitor unattended or unbalanced while searching for tools.

By following these steps, you'll be able to safely place the monitor on its side on a towel, ready for the next steps in the process of removing the bottom or base of the monitor.

Slide the monitor base forward to access the locking tab on the sub-base

To remove the bottom of a monitor, first ensure you have unplugged the monitor and placed it on a flat surface, preferably on its side on a towel to avoid damaging the screen.

Now, to access the locking tab on the sub-base, slide the monitor base forward. The sub-base is connected to the bottom of the monitor, and the base pivots on the sub-base.

Once you have located the locking tab, pull it up with your thumb and slide the sub-base toward the front of the monitor. This will allow you to remove the sub-base and base away from the monitor.

It is important to note that the process of removing the base may vary depending on the type of monitor you own. The instructions provided here are specifically for standard monitors that have a sub-base attaching the base to the monitor. LCD flat-screen monitors, for example, typically have a base that locks onto a stem at the back of the monitor.

Pull up on the locking tab and slide the sub-base towards the front of the monitor

To remove the bottom of a ViewSonic monitor, you must first place a towel on a flat surface and lay the monitor on its side on the towel. This is to avoid damaging the screen, as many standard monitors use a curved screen.

Next, slide the monitor base forward to access the locking tab on the sub-base. The sub-base is connected to the bottom of the monitor, and the base pivots on the sub-base.

Now, pull up on the locking tab with your thumb and slide the sub-base toward the front of the monitor. This will allow you to remove the sub-base and base away from the monitor.

Be sure to unplug the monitor power cord from the outlet and disconnect the monitor from the computer before removing the base.

If you are removing the base of an LCD flat-screen ViewSonic monitor, the process is slightly different. In this case, the base locks onto a stem on the back of the monitor. To remove the base, turn the locking knob on the bottom of the base counterclockwise 90 degrees with your fingers and pull the base off the monitor.

Frequently asked questions