Efficiently Cutting 808 Car Key Camera: A Step-By-Step Guide

The 808 Car Keys Micro Camera is a small, lightweight, and functional camera that can record both photos and videos. It is available in multiple versions, with varying features and specifications. The #16 version is one of the most popular variants, known for its high-quality video output and user-friendly configuration options.

To cut on the 808 Car Key Micro Camera, follow these steps:

1. Ensure that the camera is turned off.

2. Using a small screwdriver, carefully remove the two screws that hold the plastic case together.

3. Gently pry open the case, being cautious not to damage any internal components.

4. Locate the battery module, which is typically a rechargeable lithium-ion or lithium-polymer battery with a protection circuit.

5. Using a soldering iron, carefully disconnect the battery wires from the circuit board.

6. Cut the battery wires to the desired length, taking into account the space needed for the new key blade.

7. Strip the insulation from the ends of the wires.

8. Solder the wires to the new key blade, ensuring a secure connection.

9. Reassemble the camera, making sure all components are securely in place.

10. Test the camera to ensure it is functioning properly.

How to use the 808 #16 car key camera

Charging the Camera

Before using the camera for the first time, ensure that it is fully charged. You can do this by connecting the camera to a computer using a standard USB cable. When charging, the green LED will be on. Charging takes about 2.5 hours for a fully discharged battery.

Inserting an SD Card

The 808 #16 camera supports microSD cards up to 32GB in size. To insert an SD card, first locate the SD card slot, which is found next to the USB connection. Then, insert the microSD card into the slot, ensuring that the gold contacts are facing upwards. You should feel a distinct spring action when inserting the card, and there should be no friction.

Taking Photos and Videos

To turn on the camera, press and hold the power button for a maximum of 2 seconds until the red LED turns on. The camera will then be in photo mode, indicated by the red LED. To take a photo, simply press the shutter button.

To switch to video mode, briefly press the power button. The camera will now be in video recording standby mode, indicated by the yellow LED. To start recording, briefly press the shutter button. The yellow LED will flash three times to indicate that recording has started. To stop recording, briefly press the shutter button again.

Using the Camera as a Webcam

To use the 808 #16 camera as a webcam, first remove the flash memory card and connect the camera to a computer using a standard USB cable. Then, press and hold the power button for a maximum of 2 seconds until the red LED turns on. The yellow LED will turn on while the connection is being initialized and will turn off once the camera is connected. The camera is now in webcam mode and you can start your preferred webcam software.

Updating the Firmware

To update the firmware on the 808 #16 camera, first copy the new firmware file into the camera's flash card root folder. This can be done either with the card inserted in the camera or using an external card reader. Next, disconnect the camera from the computer and make sure it is turned off. Then, insert the flash card containing the new firmware file into the camera. Press the power button very briefly until the yellow LED turns on and begins to flash. Release the power button and wait for the firmware to be written into the camera. Do not press any buttons while the LED is on or flashing. Once the firmware is fully installed, the yellow LED will turn off and the camera will shut down.

Configuring the Camera Settings

To configure the camera settings on the 808 #16, you can use the Windows program Nr16Setup.exe or manually edit the "SYSCFG.TXT" file. The "SYSCFG.TXT" file must be in plain ASCII and should be placed in the root folder of the SD card. You can use any ASCII editor, such as Notepad, to modify the parameters. It is important not to change the sequence of the square brackets and not to configure invalid combinations.

How to charge the 808 #16 car key camera

To charge the 808 #16 car key camera, follow these steps:

• Connect one end of the standard USB cable to the camera and the other end to a USB power source, such as a wall charger, PC, or external battery.
• When charging, the green LED light on the camera will turn on.
• Charging a fully discharged battery typically takes around 2.5 hours.
• Once the charging is complete, the green LED light will turn off. However, with some batteries, the LED may not turn off immediately or may remain on for up to 4.5 hours.
• It is safe to assume that after 2.5 hours, the battery is fully charged, even if the green LED light is still on.

It is important to note that the 808 #16 camera uses a standard USB cable for charging, which is different from its predecessor, the #11 model. Do not use the special cable supplied with the #11 as it will destroy the #16 camera.

How to insert a micro SD card into the 808 #16 car key camera

To insert a micro SD card into the 808 #16 car key camera, follow these steps:

• Ensure the camera is turned off.
• Locate the micro SD card slot. It is usually found next to the USB connection.
• Insert the micro SD card into the slot, ensuring the gold contacts face upwards, towards the buttons. You should feel a distinct spring action when inserting the card, and there should be no friction.
• Push the card in until you hear a distinctive click, indicating that it is properly latched.
• Do not force the card, and never push it further than 1 mm into the camera body.
• If the metal frame of the cardholder is visible in the slot, insert the card above it (on the button side).

How to turn on the 808 #16 car key camera

To turn on the 808 #16 car key camera, you must first ensure that the device is charged. To do this, connect the camera to a computer using the supplied USB cable. The green LED light will illuminate to indicate that the device is charging. A full charge will take around 2.5 hours.

Once charged, you can turn on the camera by pressing and holding the power button for at least three seconds. The power button is the larger of the two buttons on the device, located behind the shutter button. The camera will turn on when you release the power button, and the red LED light will illuminate.

If the camera does not turn on, it may be due to a faulty battery or a problem with the battery module. Try resetting the battery module by disconnecting and reconnecting it if it has a connector. If this does not work, you may need to replace the battery or the entire camera.

How to take a photo with the 808 #16 car key camera

• Ensure that the camera is turned off.
• Insert a micro SD or micro SDHC card with a capacity of up to 32GB. It is recommended to use a quality card with a speed rating of Class 4 to avoid card compatibility issues.
• Press the power button briefly to turn on the camera. The red LED will turn on, indicating that the camera is in photo recording standby mode.
• Once the camera is on, you can switch between video and photo standby modes by briefly pressing the power button. The yellow LED indicates video standby mode, while the red LED indicates camera standby mode.
• To take a photo, briefly press the shutter button (the small button at the front). The yellow LED will flash twice and then turn back on.
• To take multiple photos, enable the Time-Lapse photo feature in the camera settings. This allows you to set a delay between each photo capture, ranging from 0.25 to 60 seconds.
• After taking photos, press and hold the power button for about 3-5 seconds to turn off the camera. The red LED may blink three times before turning off.

Remember to review the photos on your computer or device to ensure they were captured correctly. Additionally, always make sure your camera is charged before use, as a full battery will last around 45 minutes in the keychain model.

Frequently asked questions