Disassembling Hanns G Monitor: A Step-By-Step Guide

If you want to remove a Hanns G monitor, it's important to first disconnect all cables and cords to prevent breakage. Then, carefully place the monitor face down on a soft, flat surface to avoid any damage. Depending on your model, you may need to remove the stand base by pulling hard or unscrewing it. Some models have a plastic hinge on the stand that, when squeezed, will allow you to pop off the top part and reveal a set of screws. Other models may require you to remove the neck and its metal foot by unscrewing bolts and sliding the metal foot down and out. Once the stand is removed, you can proceed to open the monitor by removing the back cover. This may require prying with a flat tool, such as a small screwdriver, or unscrewing screws, depending on the model. It's important to be gentle during this process to avoid damaging the monitor.

Removing the back cover

To remove the back cover of a Hanns G monitor, you will first need to disconnect all cables and cords from the monitor to prevent breakage. Then, carefully place the monitor face down on a soft and flat surface to prevent any damage.

Next, you will need to remove the stand base. Depending on the model, this can be done in different ways. Some stands can be removed by pulling hard on the foot of the stand while the monitor is face down. Others may have a plastic hinge at the top of the stand that, when squeezed, will allow the top part to pop off, revealing a set of screws. Alternatively, the stand may just slide out from the screen. If none of these methods work, try looking for screws on the back of the monitor that, when removed, will allow the base to tilt up and come off.

Once the stand is removed, you can proceed to remove the back cover. For some models, this will involve removing screws from the corners of the monitor. However, for other models, there may be no screws, and the back cover is held in place by tabs or clips. In this case, you will need to use a prying tool to gently pry the back cover off without applying too much force, as this could damage the monitor.

It is important to note that opening your monitor may void your warranty, and you should proceed with caution. If you are unsure about any steps, it is recommended to consult a qualified service personnel for assistance.

Detaching the monitor stand

To detach the monitor stand from a Hanns G monitor, follow these steps:

First, disconnect all cables and cords from the monitor to prevent breakage. This includes power and video cables. Ensure that the power cable is disconnected from the power source before proceeding.

Next, carefully place the monitor face down on a soft, flat surface, such as a blanket, foam, or cloth. This will prevent any damage to the screen during the disassembly process.

Now, you will need to release the retaining plastic tabs that hold the stand in place. Squeeze the sides of the monitor to locate and depress these tabs. With the tabs released, you can now pull the stand cover off.

At this point, the process may vary slightly depending on the model of your Hanns G monitor. For some models, you will need to remove four screws to completely detach the stand base. For other models, the stand base can now be gently removed without any additional steps.

Once the stand base is removed, you will be left with a set of mount holes on the back of the monitor, which can be used to attach a VESA-compatible wall bracket for wall mounting.

It is important to note that installing an LCD monitor on a wall requires special skills and should only be performed by qualified service personnel. Improper mounting may result in accidents or injuries, so it is recommended to seek professional assistance if you are unsure about any part of the process.

Dismantling the stand base

To dismantle the stand base of a Hanns G monitor, follow these steps:

• Disconnect all cables and cords from the monitor to prevent breakage.
• Place the monitor face down on a soft, flat surface, such as a blanket, foam, or cloth, to prevent any damage to the screen.
• Squeeze the sides of the monitor to release the retaining plastic tabs.
• Pull the stand cover off.
• Remove the four screws holding the stand base in place.
• Gently lift and remove the stand base.

It is important to note that the process may vary slightly between different models of Hanns G monitors. Some models may have additional screws or tabs that need to be removed. Always refer to the specific manual for your monitor model before attempting any disassembly.

Additionally, it is recommended to seek the assistance of qualified service personnel when mounting or installing an LCD monitor. Improper mounting can result in accidents or injuries, and Hanns G bears no responsibility for any damage or injury caused by incorrect installation.

Wall mounting the monitor

To wall mount your Hanns.G monitor, you will first need to purchase a VESA-compatible wall bracket. The bracket should be VESA 100x100, with 4 holes, M4, 10mm, and 8kg capacity.

Before you begin, disconnect all cables and cords from the monitor to prevent breakage. Carefully place the monitor face down on a soft, flat surface, such as a blanket or cloth, to prevent any damage.

Now, you can remove the stand. Squeeze the sides of the monitor to release the retaining plastic tabs, and pull off the stand cover. Then, gently remove the stand base.

With the stand removed, you can fix the wall bracket firmly to your chosen position on the wall. Secure the monitor to the bracket using the four mount holes on the back and centre of the monitor. The pitch of the mounting holes is 100mm horizontally and 100mm vertically, and the required screw type is metric: M4, 10mm length.

Please note that installing an LCD monitor requires special skills and should only be performed by qualified service personnel. Hanns.G bears no responsibility for any improper mounting or resulting accidents or injuries.

Removing the monitor's front frame

To remove the front frame of a Hanns G monitor, you will first need to disconnect all cables and cords from the monitor to prevent breakage. Then, carefully place the monitor face down on a soft, flat surface, such as a blanket, foam or cloth, to prevent any damage.

Next, squeeze the sides of the monitor to release the retaining plastic tabs. You may need to apply some pressure to bow the case and allow the sides to unlatch. Once the sides are unlatched, gently pull the stand cover off.

Now, you can remove the stand base. It should just slide out from the screen. Be careful not to turn the screen upside down while holding the stand, as the screen may fall.

Finally, to remove the front frame, you will need to remove the four bolts/screws that fix the metal bracket to the frame of the monitor. You may also need to loosen the two screws at the outer left and right of the plastic back of the monitor to get some room to move.

Please note that installing an LCD monitor requires special skills and should only be performed by qualified service personnel. Attempting to do this yourself may result in accident or injury.

Frequently asked questions